HP 353803-B22 HP StorageWorks 1000 Modular Smart Array maintenance and service - Page 118

fibre subsystem link failure, 56 fibre subsystem link OK, 56 fibre switch hardware failure, 56 firmware flash done, 53 firmware flash done on box #, 53 firmware flash failed, 37 firmware flash failed on box #, 53 firmware flash started, 53 firmware flash started on box #, 53 firmware version, 35 FW version is not supported, 38 hard drive failure box, 46 hard drive hot added box bay, 46 hard drive hot removed box bay, 46 hard drive position change detected, 46 hard drive position charge invalid, 46 I2C read failure, 38 I2C write failure, 38 initializing fibre subsystem, 55 initializing PCI subsystem, 55 initializing redundancy support, 39 initializing SCSI subsystem, 37 invalid config box, 47 invalid SCSI cabling, 55 MSA1000 active controller, 42 MSA1000 standby controller, 42 new volume(s) detected, 49 no cache module found, 43 no volumes detected, 49 non-compaq hard drive, 46 obsolete cache data deleted, 44 online upgrade complete, 37 online upgrade flashing done, 37 online upgrade flashing failed, 37 online upgrade flashing firmware, 37 online upgrade flashing started, 37 online upgrade incomplete, 37 online upgrade redundancy halted, 37 online upgrade restarting system, 37 PCI bridge ASIC self-test failure, 55 PCI subsystem hardware failure, 55 persistent mem disabled, 57 persistent mem enabled, 57 pilot 2 contrlr not supported, 36 recovery ROM autoflash done, 52 recovery ROM autoflash failed, 52 recovery ROM autoflash started, 51 redundancy active active controller, 39 redundancy active standby controller, 39 redundancy failed cache Dimms mismatch, 42 redundancy failed cache size mismatch, 40 redundancy failed firmware lockup, 41 redundancy failed hardware failure, 39 redundancy failed I/O request error, 41 redundancy failed mismatch firmware, 40 redundancy failed mismatch hardware, 40 redundancy failed no second controller, 42 redundancy failed out-of-memory, 41 redundancy failed PCI Bus error, 42 redundancy halted expand active, 40 redundancy halted firmware cloned, 41 remove other controller now , 42 replacement hard drive found box, 45 restarting system, 36 ROM cloning done, 52 ROM cloning failed, 52 ROM cloning started, 52 scanning SCSI subsystem, 37 smart hard drive alert box, 46 spares cleared, 50 startup complete, 35 storage box EMU not responding, 55 storage box EMU version, 55 storage box fan degraded, 54 storage box fan failed, 53 storage box fan hot inserted, 54 storage box fan hot removed, 54 storage box fan OK, 53 storage box hot added, 55 storage box hot removed, 55 storage box overheated, 54 storage box overheating, 54 storage box power supply added, 54 storage box power supply failed, 54 storage box power supply ok, 54 storage box power supply removed, 54 storage box temperature ok, 54 system halted for cache error, 44 system name, 36 too many volumes detected, 50 uncorrected ECC memory, 56 unknown I/O module detected, 57 valid cache data found at power up, 43 volume expansion disabled, 48 volume expansion failure, 49 volume initializing parity, 48 volume media exchanged, 49 volume rebuild failure, 49 volume state deleted, 49 volume state disabled, 47 volume state expansion active, 47 volume state failed, 47 volume state interim recovery, 47 volume state missing drives, 48 volume state ok, 47 volume state rebuilding, 47 volume state waiting to expand, 48 volume state waiting to rebuild, 48 volume state wrong hard drive replaced, 48 conventions document, 10 text symbols, 10 cord. See power cord, 115 current rating, 115 customer self repair, 11, 60 D declaration of conformity, 112 118