HP 353803-B22 HP StorageWorks 1000 Modular Smart Array maintenance and service - Page 119
Class A Equipment, compliance notice
UPC - 808736781619
View all HP 353803-B22 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 119 highlights
device preparation removing power, 70 warnings and precautions, 65 device, unloading from pallet, 64 diagnostic tools, 29 disposal, battery, 114, 115 dissipating floor mats, 116 document conventions, 10 prerequisites, 9 related documentation, 9 documentation HP website, 9 providing feedback, 11 E electrostatic damage prevention, 115 electrostatic discharge See ESD, 62 electrostatic discharge See ESD, 115 electrostatic sensitive parts handling, 62 packaging, 62 storing, 62 transporting, 62 enclosure expansion ACU, 96 ACU-XE, 96 adding enclosures to existing MSA, 95, 95 attaching SCSI cables, 95 rack considerations, 95, 95 recommended procedures, 95 error messages access control conflict detected, 50 access control resources exceeded, 50 array controller disabled, 51 array controller overheated, 51 array controller overheating, 51 bad hard drive firmware box, 46 bad SCSI bus mode non-LVD device found, 38 bad scsi target, 38 cache data lost battery dead, 43 cache hardware batteries, 45 cache hardware failed and disabled, 43 chassis nvram contents corrupted, 39 cloning refused system halted, 37 controller too old not supported, 36 critical lockup detected, 35 dual cache module size mismatch, 43 EMU flash failed, 53 fibre device hardware failure, 56 fibre subsystem hardware failure, 56 fibre subsystem link failure, 56 fibre switch hardware failure, 56 firmware flash failed, 37 firmware flash failed on box #, 53 fw version is not supported, 38 hard drive failure box, 46 I2C read failure, 38 I2C write failure, 38 invalid config box 3, bay, 47 invalid SCSI cabling, 55 no cache module found, 43 online upgrade flashing failed, 37 online upgrade incomplete, 37 PCI bridge ASIC self-test failure, 55 PCI subsystem hardware failure, 55 pilot 2 contrlr not supported, 36 recovery ROM autoflash failed, 52 redundancy failed cache Dimms mismatch, 42 redundancy failed cache size mismatch, 40 redundancy failed firmware lockup, 41 redundancy failed hardware failure, 39 redundancy failed I/O request error, 41 redundancy failed mismatch firmware, 40 redundancy failed mismatch hardware, 40 redundancy failed no second controller, 42 redundancy failed out-of-memory, 41 redundancy failed PCI Bus error, 42 remove other controller now, 42 ROM cloning failed, 52 storage box EMU not responding, 55 storage box fan degraded, 54 storage box fan failed, 53 storage box overheated, 54 storage box overheating, 54 storage box power supply failed, 54 system halted for cache error, 44 too many volumes detected, 50 uncorrected ECC memory, 56 unknown I/O module detected, 57 volume expansion failure, 49 volume rebuild failure, 49 volume state disabled, 47 volume state failed, 47 volume state missing drives, 48 volume state wrong hard drive replaced, 48 ESD (electrostatic discharge) obtaining additional information, 116 precautions, 62, 115 preventing, 62 prevention measures, 115 storing products, 115 transporting products, 115 types of damage from, 115 European Union, regulatory compliance notice, 113 F fault tolerance, removing hard drives, 73 FCC (Federal Communications Commission) Class A Equipment, compliance notice, 111 Class B Equipment, compliance notice, 111 declaration of conformity, 112 modifications, 112 notice, 111 maintenance and service guide 119