HP 353803-B22 HP StorageWorks 1000 Modular Smart Array maintenance and service - Page 56

MEMORY ERROR SEEN, the Fibre Channel I/O bay.

Get HP 353803-B22 - StorageWorks Modular Smart Array 1000 SAN Starter PDF manuals and user guides
UPC - 808736781619
View all HP 353803-B22 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Message 511 FIBRE CHANNEL SUBSYSTEM HARDWARE FAILURE Type Error 513 UNCORRECTED ECC Error MEMORY ERROR SEEN 514 FIBRE SWITCH HARDWARE FAILURE Error 515 FIBRE DEVICE HARDWARE FAILURE Error 516 FIBRE SUBSYSTEM Error LINK FAILURE Description Action The array controller's Fibre Channel subsystem has encountered a critical error during the power up sequence. Remove the failed array controller and its associated Fibre Channel module, reseat the Fibre Channel daughter card on the array controller, wait 10 seconds, then reinsert the Fibre Channel module and the array controller, ensuring that they are fully seated in their respective bays in the chassis. Should the issue persist, contact HP support. The array controller has detected an uncorrectable error in the ECC memory on the memory cache board. Remove the failed array controller and replace the memory cache board with a new one. The embedded switch in the Fibre Channel I/O bay is not responding correctly or is not working. (Please note that some switches take several minutes to start up.) Remove the embedded switch, wait 10 seconds, and then reinsert the switch, ensuring that it is fully seated in the chassis. Should the issue persist, contact HP support. The array controller firmware does not recognize the device in the Fibre Channel I/O bay. The device has failed or is not supported by the installed firmware version. If the device was not recently installed or the firmware was not recently downgraded, remove the embedded device, wait 10 seconds, and then reinsert the device, ensuring that it is fully seated in the chassis. Should the issue persist, contact HP support. The controller is not currently linked to anything. This could be due to the following: • The Fibre Channel cable is not connected. • The device to which it is connected is currently not working. • The MSA is connected to a device that with an incompatible port type. Check the connections on both ends of the Fibre Channel cables and make sure that the switch, hub, or other system that the fibre is connected to is operating properly and is properly configured. Should the issue persist, contact HP support. 517 FIBRE SUBSYSTEM Informational LINK OK The Fibre Channel port has transitioned to an online state. 56 LCD panel and message descriptions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Message
Type
Description
Action
511 FIBRE CHANNEL
SUBSYSTEM HARDWARE
FAILURE
Error
The array controller's Fibre
Channel subsystem has
encountered a critical
error during the power up
sequence.
Remove the failed array
controller and its associated
Fibre Channel module,
reseat the Fibre Channel
daughter card on the array
controller, wait 10 seconds,
then reinsert the Fibre
Channel module and the
array controller, ensuring
that they are fully seated in
their respective bays in the
chassis.
Should the issue persist,
contact HP support.
513 UNCORRECTED ECC
MEMORY ERROR SEEN
Error
The array controller has
detected an uncorrectable
error in the ECC memory on
the memory cache board.
Remove the failed array
controller and replace the
memory cache board with a
new one.
514 FIBRE SWITCH
HARDWARE FAILURE
Error
The embedded switch in the
Fibre Channel I/O bay is
not responding correctly or
is not working. (Please note
that some switches take
several minutes to start up.)
Remove the embedded
switch, wait 10 seconds,
and then reinsert the switch,
ensuring that it is fully seated
in the chassis.
Should the issue persist,
contact HP support.
515 FIBRE DEVICE
HARDWARE FAILURE
Error
The array controller
fi
rmware does not
recognize the device in
the Fibre Channel I/O bay.
The device has failed or
is not supported by the
installed
fi
rmware version.
If the device was not recently
installed or the
fi
rmware was
not recently downgraded,
remove the embedded
device, wait 10 seconds,
and then reinsert the device,
ensuring that it is fully seated
in the chassis.
Should the issue persist,
contact HP support.
516 FIBRE SUBSYSTEM
LINK FAILURE
Error
The controller is not currently
linked to anything. This
could be due to the
following:
•
The Fibre Channel cable
is not connected.
•
The device to which it
is connected is currently
not working.
•
The MSA is connected
to a device that with an
incompatible port type.
Check the connections
on both ends of the Fibre
Channel cables and make
sure that the switch, hub, or
other system that the
fi
bre is
connected to is operating
properly and is properly
con
fi
gured.
Should the issue persist,
contact HP support.
517 FIBRE SUBSYSTEM
LINK OK
Informational
The Fibre Channel port has
transitioned to an online
state.
56
LCD panel and message descriptions