HP 353803-B22 HP StorageWorks 1000 Modular Smart Array maintenance and service - Page 91

Installing the component, Verifying proper operation, Replacing the power button module

Get HP 353803-B22 - StorageWorks Modular Smart Array 1000 SAN Starter PDF manuals and user guides
UPC - 808736781619
View all HP 353803-B22 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Installing the component 1. Slide the replacement SCSI I/O module into the bay until it clicks into place. 15560 2. Reconnect all SCSI cables. NOTE: Ensure that all of the SCSI cable connectors are fastened tightly. Verifying proper operation After replacing the failed SCSI I/O module, verify that: • The module status LED is solid green. • No new error messages are displayed on the array controller LCD panel. Replacing the power button module CAUTION: The power button module is not hot-pluggable. Before replacing the module, all I/O from the servers must be stopped and the MSA must be powered down. Before you begin CAUTION: • Before removing a component or blanking panel from an operational device, make sure that you have the replacement part available. Removing a component or blank impacts the airflow and cooling ability of the device. To avoid possible overheating, insert the new or replacement component within one or two minutes. If the internal temperature exceeds acceptable limits, the device may overheat and automatically shut down or restart. • Parts can be damaged by electrostatic discharge. Use proper anti-static protection. maintenance and service guide 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Installing the component
1.
Slide the replacement SCSI I/O module into the bay until it clicks into place.
15560
2.
Reconnect all SCSI cables.
NOTE:
Ensure that all of the SCSI cable connectors are fastened tightly.
Verifying proper operation
After replacing the failed SCSI I/O module, verify that:
•
The module status LED is solid green.
•
No new error messages are displayed on the array controller LCD panel.
Replacing the power button module
CAUTION:
The power button module is not hot-pluggable. Before replacing the module, all I/O from the servers
must be stopped and the MSA must be powered down.
Before you begin
CAUTION:
•
Before removing a component or blanking panel from an operational device, make sure that you
have the replacement part available. Removing a component or blank impacts the air
fl
ow and
cooling ability of the device. To avoid possible overheating, insert the new or replacement component
within one or two minutes. If the internal temperature exceeds acceptable limits, the device may
overheat and automatically shut down or restart.
•
Parts can be damaged by electrostatic discharge. Use proper anti-static protection.
maintenance and service guide
91