HP 353803-B22 HP StorageWorks 1000 Modular Smart Array maintenance and service - Page 86

Replacing a power supply/fan assembly, Before you begin, Verifying component failure

Get HP 353803-B22 - StorageWorks Modular Smart Array 1000 SAN Starter PDF manuals and user guides
UPC - 808736781619
View all HP 353803-B22 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Verifying proper operation After replacing the failed SFP, verify that: • The 1-Gb and 2-Gb link-status LEDs on the Fibre Channel I/O module cycle through blinking amber and green and then Off to indicate that the circuitry has recognized a newly installed SFP. • The status LED on the Fibre Channel I/O module is solid green. • No new error messages are displayed on the array controller LCD panel. Replacing a power supply/fan assembly The assembly is hot-pluggable, so it is not necessary to power down the system to replace it. Before you begin CAUTION: • Before removing a component or blanking panel from an operational device, make sure that you have the replacement part available. Removing a component or blank impacts the airflow and cooling ability of the device. To avoid possible overheating, insert the new or replacement component within one or two minutes. If the internal temperature exceeds acceptable limits, the device may overheat and automatically shut down or restart. • Parts can be damaged by electrostatic discharge. Use proper anti-static protection. CAUTION: • Replacement power supply assemblies do not include a variable speed fan. You must remove the operational fan from the defective power supply and install the fan on the new power supply. • The fan blades rotate at a high speed and do not stop immediately when power is removed from the MSA. Allow time for the blades to stop rotating. Avoid touching the rotating blades when removing the fan. • The fan shell must be handled carefully to avoid breaking it. Do not press on the center section of the fan shell (circular panel covering the blades). To avoid damaging the fan blades, grasp only the outer portion of the fan shell. Do not rest the power supply on the fan. Doing so might break the fan. Verifying component failure • Check the array controller LCD display panel for error messages. • Verify that the electrical source is delivering power down the AC power cord. • Verify that the power supply fault LED is flashing amber. • Verify that the power supply Power on/off LED is Off. Removing the component 1. Review all warnings, cautions, and preparation procedures as detailed in Warnings and precautions. 2. Disengage the cord lock and disconnect the AC power cord from the failed power supply. CAUTION: When removing the left power supply, move the cord lock on the right power supply out of the way to avoid dislodging the right power supply and causing your system to become overheated. 86 Customer replaceable components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Verifying proper operation
After replacing the failed SFP, verify that:
•
The 1-Gb and 2-Gb link-status LEDs on the Fibre Channel I/O module cycle through blinking amber
and green and then Off to indicate that the circuitry has recognized a newly installed SFP.
•
The status LED on the Fibre Channel I/O module is solid green.
•
No new error messages are displayed on the array controller LCD panel.
Replacing a power supply/fan assembly
The assembly is hot-pluggable, so it is not necessary to power down the system to replace it.
Before you begin
CAUTION:
•
Before removing a component or blanking panel from an operational device, make sure that you
have the replacement part available. Removing a component or blank impacts the air
fl
ow and
cooling ability of the device. To avoid possible overheating, insert the new or replacement component
within one or two minutes. If the internal temperature exceeds acceptable limits, the device may
overheat and automatically shut down or restart.
•
Parts can be damaged by electrostatic discharge. Use proper anti-static protection.
CAUTION:
•
Replacement power supply assemblies do not include a variable speed fan. You must remove the
operational fan from the defective power supply and install the fan on the new power supply.
•
The fan blades rotate at a high speed and do not stop immediately when power is removed from
the MSA. Allow time for the blades to stop rotating. Avoid touching the rotating blades when
removing the fan.
•
The fan shell must be handled carefully to avoid breaking it. Do not press on the center section of the
fan shell (circular panel covering the blades). To avoid damaging the fan blades, grasp only the
outer portion of the fan shell. Do not rest the power supply on the fan. Doing so might break the fan.
Verifying component failure
•
Check the array controller LCD display panel for error messages.
•
Verify that the electrical source is delivering power down the AC power cord.
•
Verify that the power supply fault LED is
fl
ashing amber.
•
Verify that the power supply Power on/off LED is Off.
Removing the component
1.
Review all warnings, cautions, and preparation procedures as detailed in
Warnings and precautions
.
2.
Disengage the cord lock and disconnect the AC power cord from the failed power supply.
CAUTION:
When removing the left power supply, move the cord lock on the right power supply out of
the way to avoid dislodging the right power supply and causing your system to become
overheated.
86
Customer replaceable components