HP Rp3000 Service Reference Guide: HP rp3000 Point of Sale - Page 71

CAUTION, Connecting the Optical Drive Power and Data Cables

Get HP Rp3000 - Point of Sale System PDF manuals and user guides
UPC - 884420494096
View all HP Rp3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

NOTE: When replacing a drive, use the four retainer screws that were used for the old drive when installing the new drive. To install an optical drive: 1. Follow the procedure above to remove the old optical drive. 2. If necessary, remove the bezel blank covering the 5.25-inch drive bay. 3. Slide the drive into the optical drive bay (1) and secure it in place with the four retainer screws (2). Figure 6-38 Installing the Optical Drive 4. Connect the power cable (1) and data cable (2) to the rear of the optical drive. Figure 6-39 Connecting the Optical Drive Power and Data Cables CAUTION: Never crease or bend a SATA data cable tighter than a 30 mm (1.18 in) radius. A sharp bend can break the internal wires. 5. Connect the other end of the SATA data cable to the white system board connector labeled SATA 1. Drives 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
NOTE:
When replacing a drive, use the four retainer screws that were used for the old drive when
installing the new drive.
To install an optical drive:
1.
Follow the procedure above to remove the old optical drive.
2.
If necessary, remove the bezel blank covering the 5.25-inch drive bay.
3.
Slide the drive into the optical drive bay
(1)
and secure it in place with the four retainer screws
(2)
.
Figure 6-38
Installing the Optical Drive
4.
Connect the power cable
(1)
and data cable
(2)
to the rear of the optical drive.
Figure 6-39
Connecting the Optical Drive Power and Data Cables
CAUTION:
Never crease or bend a SATA data cable tighter than a 30 mm (1.18 in) radius. A
sharp bend can break the internal wires.
5.
Connect the other end of the SATA data cable to the white system board connector labeled SATA
1.
Drives
63