HP Scitex LX850 HP Scitex LX850 & LX820 Printers: User's Guide - English - Page 12

Fire hazard, Mechanical hazard

Get HP Scitex LX850 PDF manuals and user guides View all HP Scitex LX850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Introduction Fire hazard The drying and curing subsystems of the printer operate at high temperatures. Call your service representative if the printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) is repeatedly tripped. To avoid the risk of fire, take the following precautions. ● Use the power supply voltage specified on the nameplate. ● Connect the power cords to dedicated lines, each protected by a branch circuit breaker according to the information detailed in the Site Preparations documentation. ● Do not insert objects through slots in the printer. ● Take care not to spill liquid on the printer. ● Do not use aerosol products that contain flammable gases inside or around the printer. ● Do not block or cover the openings of the printer. ● Do not attempt to dismantle the drying or curing module, or the electrical control cabinet. ● Ensure that the operating temperature of the substrate loaded recommended by the manufacturer is not exceeded. If this information is not available by the manufacturer, do not load substrates that cannot be used at an operating temperature under 125°C (257°F). ● Do not load substrates with auto-ignition temperatures below 250°C (482°F). See note below. NOTE: Test method based on EN ISO 6942:2002; Evaluation of materials and material assemblies when exposed to a source of radiant heat, method B. The test conditions, to determine the temperature when the substrate starts ignition (either flame or glow) were: Heat flux density: 30 kW/m2, Copper calorimeter, K type thermocouple. Mechanical hazard The printer has moving parts that could cause injury. To avoid personal injury, take the following precautions when working close to the printer. ● Keep your clothing and all parts of your body away from the printer's moving parts. ● Avoid wearing necklaces, bracelets and other hanging objects. ● If your hair is long, try to secure it so that it will not fall into the printer. ● Take care that sleeves or gloves do not get caught in the printer's moving parts. ● Avoid standing close to the fans, which could cause injury and could also affect print quality (by obstructing the air flow). ● Do not touch gears or moving rolls during printing. 8 Chapter 1 Introduction ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Fire hazard
The drying and curing subsystems of the printer operate at high temperatures. Call your service
representative if the printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) is
repeatedly tripped.
To avoid the risk of fire, take the following precautions.
●
Use the power supply voltage specified on the nameplate.
●
Connect the power cords to dedicated lines, each protected by a branch circuit breaker according
to the information detailed in the Site Preparations documentation.
●
Do not insert objects through slots in the printer.
●
Take care not to spill liquid on the printer.
●
Do not use aerosol products that contain flammable gases inside or around the printer.
●
Do not block or cover the openings of the printer.
●
Do not attempt to dismantle the drying or curing module, or the electrical control cabinet.
●
Ensure that the operating temperature of the substrate loaded recommended by the manufacturer
is not exceeded. If this information is not available by the manufacturer, do not load substrates
that cannot be used at an operating temperature under 125°C (257°F).
●
Do not load substrates with auto-ignition temperatures below 250°C (482°F). See note below.
NOTE:
Test method based on EN ISO 6942:2002; Evaluation of materials and material
assemblies when exposed to a source of radiant heat, method B. The test conditions, to determine
the temperature when the substrate starts ignition (either flame or glow) were: Heat flux density:
30 kW/m2, Copper calorimeter, K type thermocouple.
Mechanical hazard
The printer has moving parts that could cause injury. To avoid personal injury, take the following
precautions when working close to the printer.
●
Keep your clothing and all parts of your body away from the printer's moving parts.
●
Avoid wearing necklaces, bracelets and other hanging objects.
●
If your hair is long, try to secure it so that it will not fall into the printer.
●
Take care that sleeves or gloves do not get caught in the printer's moving parts.
●
Avoid standing close to the fans, which could cause injury and could also affect print quality (by
obstructing the air flow).
●
Do not touch gears or moving rolls during printing.
8
Chapter 1
Introduction
ENWW
Introduction