HP Scitex LX850 HP Scitex LX850 & LX820 Printers: User's Guide - English - Page 57

Load a roll (roll-to-free-fall with collector configuration) (LX850 only), Move to printing, custom

Get HP Scitex LX850 PDF manuals and user guides View all HP Scitex LX850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

18. If you intend to use full bleed, do not use the substrate edge holders, but use Move to printing (custom) to raise the carriage. Do not remove the edge holders; just move them aside at each end of the platen. 19. If you do not intend to use full bleed, use the substrate edge holders to prevent the substrate edges from lifting up and jamming while printing. See The substrate edge holders on page 27. 20. Go to the HP Internal Print Server and press the Load button. The printer rotates the input roll to check its diameter, and it also checks the width of the roll, the winding direction, the vacuum and the substrate advance calibration (this takes 1-2 min). NOTE: Some substrates (such as transparent substrates) cannot be measured by the printer in this way. In such cases, you will be asked to enter the required information manually. Use the scale on the curing module to see the value for the right-hand edge that must be entered manually in the HP Internal Print Server. 21. In the HP Internal Print Server, choose from the list of substrate types the type that you have loaded. Handle the substrate The contents of the Loaded Substrate window are determined automatically when the substrate is loaded and checked. However, if the printer is unable to detect the edges of the substrate (for instance, in the case of a transparent substrate), you will have to measure the distance of the left edge from the printer's side plate, and complete the Left Edge and Width fields yourself. For more information on when you might want to change the carriage beam position, see Substrate tips on page 21. An alert regarding substrate advance tracking may appear at this point. For more information on when you might want to turn off automatic tracking, see Fine-tune the settings in your new preset on page 67 and the Maintenance and troubleshooting guide. The printer is now ready to print. Load a roll (roll-to-free-fall with collector configuration) (LX850 only) ENWW Load a roll into the printer 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
18.
If you intend to use full bleed, do not use the substrate edge holders, but use
Move to printing
(custom)
to raise the carriage. Do not remove the edge holders; just move them aside at each
end of the platen.
19.
If you do not intend to use full bleed, use the substrate edge holders to prevent the substrate edges
from lifting up and jamming while printing. See
The substrate edge holders
on page
27
.
20.
Go to the HP Internal Print Server and press the
Load
button. The printer rotates the input roll to
check its diameter, and it also checks the width of the roll, the winding direction, the vacuum and
the substrate advance calibration (this takes 1–2 min).
NOTE:
Some substrates (such as transparent substrates) cannot be measured by the printer in
this way. In such cases, you will be asked to enter the required information manually. Use the
scale on the curing module to see the value for the right-hand edge that must be entered manually
in the HP Internal Print Server.
21.
In the HP Internal Print Server, choose from the list of substrate types the type that you have
loaded.
The contents of the Loaded Substrate window are determined automatically when the substrate is
loaded and checked. However, if the printer is unable to detect the edges of the substrate (for
instance, in the case of a transparent substrate), you will have to measure the distance of the left
edge from the printer's side plate, and complete the Left Edge and Width fields yourself.
For more information on when you might want to change the carriage beam position, see
Substrate tips
on page
21
.
An alert regarding substrate advance tracking may appear at this point. For more information on
when you might want to turn off automatic tracking, see
Fine-tune the settings in your new preset
on page
67
and the
Maintenance and troubleshooting guide
.
The printer is now ready to print.
Load a roll (roll-to-free-fall with collector configuration) (LX850
only)
ENWW
Load a roll into the printer
53
Handle the substrate