HP Scitex LX850 HP Scitex LX850 & LX820 Printers: User's Guide - English - Page 16

Basic setup options, Turn the printer on and off, Personal settings

Get HP Scitex LX850 PDF manuals and user guides View all HP Scitex LX850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Personal settings 2 Basic setup options Turn the printer on and off The printer has two levels of power consumption. ● Electronics on: The electronic components that use relatively little power are turned on. ● Everything on: All components are turned on, including the mechanical and drying components that use more power. To turn on the printer: 1. Make sure that all the circuit breakers are in the up position (ACB1, ACB2, ACB3, RCB1). 2. Turn the big switch at the rear left of the printer to the on position. 3. Check that all four red lights are on (three for the three-phase line and one for the single-phase). In normal operation these lights should always be on. If any of them are off, check the front panel in case there is a system error, and consult the Maintenance and troubleshooting guide or check with your electrician. 12 Chapter 2 Basic setup options ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
2
Basic setup options
Turn the printer on and off
The printer has two levels of power consumption.
●
Electronics on: The electronic components that use relatively little power are turned on.
●
Everything on: All components are turned on, including the mechanical and drying components
that use more power.
To turn on the printer:
1.
Make sure that all the circuit breakers are in the up position (ACB1, ACB2, ACB3, RCB1).
2.
Turn the big switch at the rear left of the printer to the on position.
3.
Check that all four red lights are on (three for the three-phase line and one for the single-phase). In
normal operation these lights should always be on. If any of them are off, check the front panel in
case there is a system error, and consult the
Maintenance and troubleshooting guide
or check with
your electrician.
12
Chapter 2
Basic setup options
ENWW
Personal settings