HP Scitex LX850 HP Scitex LX850 & LX820 Printers: User's Guide - English - Page 35

Uninstall the kit, Substrate, Unload, Ink collector

Get HP Scitex LX850 PDF manuals and user guides View all HP Scitex LX850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Handle the substrate ● In the roll-to-free-fall configuration, the output diverter is not needed. ● In the roll-to-roll configuration, you are recommended to use both diverters, but in some cases you may be able to minimize wrinkles by changing the position of a diverter or even by removing one or both of them. 13. Check that the curing plates are in the correct position for the substrate you are loading (see The curing plates on page 32). 14. Load the substrate, which should pass outside the input diverter and inside the output diverter. 15. Deploy the edge holders. 16. If you have not already done so, go to the HP Internal Print Server and select Substrate > Load/ Unload. In the load configuration, ensure that the Ink collector box is checked. 17. Lower the carriage beam to the normal position. 18. You may need to enter the left edge position and the substrate width into the HP Internal Print Server, if the printer cannot detect them. Uninstall the kit The ink collector kit must be uninstalled before printing on non-porous substrates. 1. Raise the carriage beam to its highest position. 2. If any substrate is loaded, unload it. Take care that it does not touch the ink collector foams, which may be wet with ink. 3. Remove the edge holders, and clean them if necessary. 4. Remove the diverter rollers. ENWW The ink collector kit (LX850 only) 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
●
In the roll-to-free-fall configuration, the output diverter is not needed.
●
In the roll-to-roll configuration, you are recommended to use both diverters, but in some cases
you may be able to minimize wrinkles by changing the position of a diverter or even by
removing one or both of them.
13.
Check that the curing plates are in the correct position for the substrate you are loading (see
The
curing plates
on page
32
).
14.
Load the substrate, which should pass outside the input diverter and inside the output diverter.
15.
Deploy the edge holders.
16.
If you have not already done so, go to the HP Internal Print Server and select
Substrate
>
Load/
Unload
. In the load configuration, ensure that the
Ink collector
box is checked.
17.
Lower the carriage beam to the normal position.
18.
You may need to enter the left edge position and the substrate width into the HP Internal Print
Server, if the printer cannot detect them.
Uninstall the kit
The ink collector kit must be uninstalled before printing on non-porous substrates.
1.
Raise the carriage beam to its highest position.
2.
If any substrate is loaded, unload it. Take care that it does not touch the ink collector foams, which
may be wet with ink.
3.
Remove the edge holders, and clean them if necessary.
4.
Remove the diverter rollers.
ENWW
The ink collector kit (LX850 only)
31
Handle the substrate