HP Scitex LX850 HP Scitex LX850 & LX820 Printers: User's Guide - English - Page 59

Enable collector, Outwards, Inwards, Select the winding direction

Get HP Scitex LX850 PDF manuals and user guides View all HP Scitex LX850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

● 2642 mm (104 in): two 1067-mm (42-in), 305-mm (12-in) and 203-mm (8-in) tubes ● 3200 mm (126 in): two 1067-mm (42-in), 610-mm (24-in), 305-mm (12-in) and 152-mm (6-in) tubes 1. Follow the whole loading procedure for the roll-to-free-fall configuration. 2. Load an empty substrate core onto the collector spindle. For dual-roll printing, load two cores of the same diameter onto a single spindle (it is not recommended to use a dual-roll spindle as the collector). 3. Use the buttons on the front panel to advance the substrate's leading edge until it reaches the core on the collector. 4. Tighten the substrate so that it is evenly tensioned, then attach the leading edge to the core with tape, first at the center and then at the sides. There should be no wrinkles or slackness across the substrate. Handle the substrate 5. Use the buttons on the front panel again to advance the substrate so that a substrate loop is produced between the tension roller and the collector. 6. Place the loop shaper into the substrate loop. NOTE: Loop detection is done on the right-hand side of the printer; so avoid putting your foot or any other object under the collector on the right-hand side. 7. Go to the HP Internal Print Server and press the Enable collector button. 8. Select the winding direction: Outwards is recommended, as it permits an output roll up to 230 mm (9 in) in diameter. If you select Inwards, the diameter of the output roll is limited to 150 mm (5.9 in). NOTE: The winding direction cannot be changed on the fly: the collector has to be deactivated and reactivated. ENWW Load a roll into the printer 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
●
2642 mm (104 in): two 1067-mm (42-in), 305-mm (12-in) and 203-mm (8-in) tubes
●
3200 mm (126 in): two 1067-mm (42-in), 610-mm (24-in), 305-mm (12-in) and 152-mm (6-in)
tubes
1.
Follow the whole loading procedure for the roll-to-free-fall configuration.
2.
Load an empty substrate core onto the collector spindle. For dual-roll printing, load two cores of
the same diameter onto a single spindle (it is not recommended to use a dual-roll spindle as the
collector).
3.
Use the buttons on the front panel to advance the substrate's leading edge until it reaches the core
on the collector.
4.
Tighten the substrate so that it is evenly tensioned, then attach the leading edge to the core with
tape, first at the center and then at the sides. There should be no wrinkles or slackness across the
substrate.
5.
Use the buttons on the front panel again to advance the substrate so that a substrate loop is
produced between the tension roller and the collector.
6.
Place the loop shaper into the substrate loop.
NOTE:
Loop detection is done on the right-hand side of the printer; so avoid putting your foot or
any other object under the collector on the right-hand side.
7.
Go to the HP Internal Print Server and press the
Enable collector
button.
8.
Select the winding direction:
Outwards
is recommended, as it permits an output roll up to 230
mm (9 in) in diameter. If you select
Inwards
, the diameter of the output roll is limited to 150 mm
(5.9 in).
NOTE:
The winding direction cannot be changed on the fly: the collector has to be deactivated
and reactivated.
ENWW
Load a roll into the printer
55
Handle the substrate