IBM 8863 Service Guide - Page 146

Power, backplane

Get IBM 8863 - eServer xSeries 366 PDF manuals and user guides
UPC - 000435474667
View all IBM 8863 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

Note: You might find it helpful to note where each adapter is installed before removing the adapters. 5. Disconnect the PCI-X switch card ribbon cable from the card. 6. Lift the release latches and slide the card away from the chassis; then, remove the card from the server. To install a PCI-X switch-card assembly, complete the following steps: 1. Lower the card into place so that the lips on the bottom of the EMI shielding material fit into the chassis, and slide the card into place until the two release latches snap securely. 2. Connect the ribbon cable to the PCI-X switch-card assembly. 3. Install the adapters and adapter dividers. 4. Replace the top cover and bezel. 5. Reconnect the external cables and power cords. Power backplane Complete the following steps to remove a power backplane. 1. Read the safety information that begins on page vii, and "Handling static-sensitive devices" on page 100. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables necessary to replace the device. 3. Remove the top cover. 4. Remove all fans (see "Hot-swap fan" on page 104). 5. Remove the memory cards (see "Removing and replacing a memory card" on page 111). 6. Lift the microprocessor-tray release latch, open the microprocessor-tray levers, and pull the microprocessor tray out of the server slightly (see "Removing and installing a microprocessor" on page 124). 7. Remove the power supplies and the power-supply structure (see "Power-supply structure" on page 121). 130 IBM xSeries 366 Type 8863: Problem Determination and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Note:
You
might
find
it
helpful
to
note
where
each
adapter
is
installed
before
removing
the
adapters.
5.
Disconnect
the
PCI-X
switch
card
ribbon
cable
from
the
card.
6.
Lift
the
release
latches
and
slide
the
card
away
from
the
chassis;
then,
remove
the
card
from
the
server.
To
install
a
PCI-X
switch-card
assembly,
complete
the
following
steps:
1.
Lower
the
card
into
place
so
that
the
lips
on
the
bottom
of
the
EMI
shielding
material
fit
into
the
chassis,
and
slide
the
card
into
place
until
the
two
release
latches
snap
securely.
2.
Connect
the
ribbon
cable
to
the
PCI-X
switch-card
assembly.
3.
Install
the
adapters
and
adapter
dividers.
4.
Replace
the
top
cover
and
bezel.
5.
Reconnect
the
external
cables
and
power
cords.
Power
backplane
Complete
the
following
steps
to
remove
a
power
backplane.
1.
Read
the
safety
information
that
begins
on
page
vii,
and
“Handling
static-sensitive
devices”
on
page
100.
2.
Turn
off
the
server
and
peripheral
devices,
and
disconnect
the
power
cords
and
all
external
cables
necessary
to
replace
the
device.
3.
Remove
the
top
cover.
4.
Remove
all
fans
(see
“Hot-swap
fan”
on
page
104).
5.
Remove
the
memory
cards
(see
“Removing
and
replacing
a
memory
card”
on
page
111).
6.
Lift
the
microprocessor-tray
release
latch,
open
the
microprocessor-tray
levers,
and
pull
the
microprocessor
tray
out
of
the
server
slightly
(see
“Removing
and
installing
a
microprocessor”
on
page
124).
7.
Remove
the
power
supplies
and
the
power-supply
structure
(see
“Power-supply
structure”
on
page
121).
130
IBM
xSeries
366
Type
8863:
Problem
Determination
and
Service
Guide