Icom IC-M92D Instruction Manual - Page 101

Optional Speaker-microphone

Get Icom IC-M92D PDF manuals and user guides View all Icom IC-M92D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

12 OPTIONAL SPEAKER-MICROPHONE ■ HM-167 descriptions ■ Attachment 1 Alligator type clip To attach the speaker-microphone to your shirt or collar, etc. PTT switch Push to transmit. Release to receive. Turn power OFF before attaching the speaker-microphone. 2 Then, insert the speaker-microphone's connector into the 3 [SP MIC] connector and carefully screw it tight, as shown in the diagram below. Be careful not to cross-thread the con- 4 nection. 5 IMPORTANT: KEEP the transceiver's [SP MIC] cap attached when the speaker-microphone is not used. If the cover is not 6 Microphone Speaker attached, water will get into the transceiver. Moreover, the 7 terminals (pins) will become rusty, or the transceiver will function abnormally if the connector gets wet. 8 Turn the transceiver power OFF when connecting the HM-167. Set the triangle mark K CAUTION: Attach the speaker- 9 to the back side. microphone's connector securely 10 to prevent accidental dropping, or water intrusion in the connector. 11 NEVER immerse the connector in water. If the connector becomes wet, be sure to dry it BEFORE attaching it to the transceiver. Detaching: 12 Pull up the cap 13 in the direction of the arrow to 14 NOTE: The microphone is located near the top of the speaker-microphone, as shown in the illustration above. To maximize the readability of your transmitted signal (voice), hold the microphone approximately 5 to 10 cm (2 to 4 inches) from your mouth, and speak at a normal voice level. detach it. 15 Attaching: 16 Attach the cap in the direction of the arrow completely. 94

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
94
12
OPTIONAL SPEAKER-MICROPHONE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
HM-167 descriptions
■
NEVER
immerse the connector in water. If the connector
becomes wet, be sure to dry it BEFORE attaching it to the
transceiver.
NOTE:
The microphone is located near the top of the
speaker-microphone, as shown in the illustration above.
To maximize the readability of your transmitted signal
(voice), hold the microphone approximately 5 to 10 cm
(2 to 4 inches) from your mouth, and speak at a normal
voice level.
Attachment
■
Turn power OFF before attaching the speaker-microphone.
Then, insert the speaker-microphone’s connector into the
[SP MIC] connector and carefully screw it tight, as shown in
the diagram below. Be careful not to cross-thread the con-
nection.
IMPORTANT:
KEEP
the transceiver’s [SP MIC] cap attached
when the speaker-microphone is not used. If the cover is not
attached, water will get into the transceiver. Moreover, the
terminals (pins) will become rusty, or the transceiver will
function abnormally if the connector gets wet.
Set the triangle mark
K
to the back side.
CAUTION:
Attach the speaker-
microphone’s connector securely
to prevent accidental dropping, or
water intrusion in the connector.
Detaching:
Pull up the cap
in the direction
of the arrow to
detach it.
Attaching:
Attach the cap
in the direction
of the arrow
completely.
PTT switch
Push to transmit.
Release to receive.
Microphone
Speaker
Alligator type clip
To attach the speaker-microphone
to your shirt or collar, etc.
Turn the transceiver power OFF
when connecting the HM-167.