Icom IC-M92D Instruction Manual - Page 17

Preparation

Get Icom IC-M92D PDF manuals and user guides View all Icom IC-M92D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

4 PREPARATION ■ MMSI code programming 1 The 9 digit MMSI (Maritime Mobile Service Identity: DSC self r Repeat step e to enter all 9 digits. 2 ID) code can be programmed at power ON. t After entering the 9 digit code, "FINISH" is automatically 3 This initial code setting can be performed only once. selected, and then push [ENTER] to set it. y The "MMSI CONFIRMATION" screen is displayed. 4 After being set, it can be changed by only your dealer 5 or distributor. If your MMSI code has already been programmed, this programming is not necessary. 6 7 q Hold down [ ] to turn ON the power. • Three short beeps sound, and "NO DSC MMSI" is displayed. 8 w Push [ENTER] to start the MMSI code programming. • Push [CLEAR] twice to cancel the programming, and go to the u Enter your MMSI code again for confirmation. 9 normal operating screen. In this case, the transceiver cannot make a DSC call. To program the MMSI code, turn OFF the • Enter in the same manner as steps e through t. i When your MMSI code programming is successfully com- 10 power, then turn it ON again. pleted, the screen as shown below is briefly displayed. 11 e Enter your MMSI code in the following manner: • Select a desired number using • After that, the normal operating screen is displayed. 12 • Push [ENTER] to set it. 13 • To move the cursor, select either arrow, "←" or "→," then push [ENTER]. 14 15 16 The programmed MMSI code can be checked in the MENU screen. (p. 83) 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
10
4
PREPARATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
MMSI code programming
■
The 9 digit MMSI (Maritime Mobile Service Identity: DSC self
ID) code can be programmed at power ON.
This initial code setting can be performed only once.
After being set, it can be changed by only your dealer
or distributor. If your MMSI code has already been pro-
grammed, this programming is not necessary.
Hold down [
q
] to turn ON the power.
• Three short beeps sound, and “NO DSC MMSI” is displayed.
Push [ENTER] to start the MMSI code programming.
w
•
Push [CLEAR] twice to cancel the programming, and go to the
normal operating screen. In this case, the transceiver cannot
make a DSC call. To program the MMSI code, turn OFF the
power, then turn it ON again.
Enter your MMSI code in the following manner:
e
• Select a desired number using [
∫
]/[
√
]/[
Ω
]/[
≈
].
• Push [ENTER] to set it.
•
To move the cursor, select either arrow, “
←
” or “
→
,” then push
[ENTER].
Repeat step
r
e
to enter all 9 digits.
After entering the 9 digit code, “FINISH” is automatically
t
selected, and then push [ENTER] to set it.
The “MMSI CONFIRMATION” screen is displayed.
y
Enter your MMSI code again for confirmation.
u
• Enter in the same manner as steps
e
through
t
.
When your MMSI code programming is successfully com-
i
pleted, the screen as shown below is briefly displayed.
• After that, the normal operating screen is displayed.
The programmed MMSI code can be checked in the MENU
screen. (
p. 83)