Intel S875WP1 Product Guide - Page 44

Installing the Server Board, Placing the Server Board into the Chassis

Get Intel S875WP1 - EATX MBD 875 P4 DDR-2CH SATA RAID VID GETH PDF manuals and user guides
UPC - 735858161381
View all Intel S875WP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Installing the Server Board Placing the Server Board into the Chassis When placing the board into the chassis, insert the rear I/O connector end first, carefully positioning the board's I/O connectors into the openings in the I/O shield on the back of the chassis. TP00103 Figure 9. Placing the Server Board into the Chassis Attaching the Server Board ✏ NOTES You will need a Phillips (#2 bit) screwdriver. Refer to Page 107 for regulatory requirements and installation instructions and precautions. The Intel® Server Chassis SC5200 and the Intel Server Chassis SC5250-E use different screws to attach the server board to the chassis. Be sure to use the appropriate screw for your chassis. See the diagram below for the correct screw for each chassis. WARNING Only qualified technical personnel should attempt this procedure. Disconnect the server from its power source before performing the procedures described here. Failure to disconnect the power before you open the server can result in personal injury or equipment damage. 44 Intel Server Board S875WP1-E Product Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
44
Intel Server Board S875WP1-E Product Guide
Installing the Server Board
Placing the Server Board into the Chassis
When placing the board into the chassis, insert the rear I/O connector end first, carefully
positioning the board’s I/O connectors into the openings in the I/O shield on the back of the chassis.
TP00103
Figure 9. Placing the Server Board into the Chassis
Attaching the Server Board
NOTES
You will need a Phillips (#2 bit) screwdriver.
Refer to Page 107 for regulatory requirements and installation instructions
and precautions.
The Intel® Server Chassis SC5200 and the Intel Server Chassis SC5250-E use
different screws to attach the server board to the chassis.
Be sure to use the
appropriate screw for your chassis.
See the diagram below for the correct
screw for each chassis.
WARNING
Only qualified technical personnel should attempt this procedure.
Disconnect
the server from its power source before performing the procedures described
here.
Failure to disconnect the power before you open the server can result in
personal injury or equipment damage.