Kenmore HE2t User Guide

Kenmore HE2t - 3.7 cu. Ft. Front Load Washer Manual

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Kenmore HE2t manual content summary:

  • Kenmore HE2t | User Guide - Page 1
    CONSUMER SERVICES TECHNICAL EDUCATION GROUP PRESENTS L-78 FRONT-LOADING AUTOMATIC WASHER MODELS: WFW8300SW, WFW8500SW, WFW8500SR JOB AID Part No. 8178558
  • Kenmore HE2t | User Guide - Page 2
    , "Duet Sport™ Front-Loading Automatic Washer" (Part No. 8178558), provides the technician with information on the installation, operation, and service of the Duet Sport™ Front-Loading Automatic Washer. For specific information on the model being serviced, refer to the "Use and Care Guide," or "Tech
  • Kenmore HE2t | User Guide - Page 3
    The Line Filter & Power Supply Cord 4-8 Removing The Detergent Dispenser Assembly 4-10 Removing The Detergent Dispenser Motor 4-13 Removing The Door Switch Assembly And The Bellows 4-14 Removing The Drain Pump 4-17 Removing The ECO Valve 4-19 Removing The Motor Control Unit 4-20 Removing The
  • Kenmore HE2t | User Guide - Page 4
    /Error Display Codes 6-2 Diagnostic Test 6-5 Error History Display 6-6 History Overview Test Program 6-6 Manual Diagnostic Test 6-7 Manual Overview Test Program 6-7 Electronic Assemblies - Removal Or Replacement 6-8 Washer Care 6-9 Troubleshooting Guide 6-11 WIRING DIAGRAMS 7-1 Washer
  • Kenmore HE2t | User Guide - Page 5
    ." These words mean: DANGER You can be killed or seriously injured if you don't immediately follow instructions. You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury
  • Kenmore HE2t | User Guide - Page 6
    MODEL & SERIAL NUMBER DESIGNATIONS MODEL NUMBER MODEL NUMBER W F W 8 3 00 S W 0 BRAND W = Whirlpool ACCESS F = Front Loading PRODUCT W = Washer SERIES 5 = Whirlpool Leap 7 = 24˝ Front Load 9 = Duet Front Load 6 = Oasis 8 = Mid Line Front Load PRICE POINT LEVELS (1 - 9) TRADE PARTNER ID (00
  • Kenmore HE2t | User Guide - Page 7
    MODEL & SERIAL NUMBER LABEL AND TECH SHEET LOCATIONS The Model & Serial Number Label and Tech Sheet locations are shown below. Model & Serial Number Label Tech Sheet (Behind Lower Access Panel) 1-3
  • Kenmore HE2t | User Guide - Page 8
    Control Heater Sensors Tumble Speed Spin Speed Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds Height Install Depth: Min - Max Width Product Weight (approx) WFW8300SW WFW8500SW WFW8500SR Front Load Washer Front Load Washer Front Load Washer
  • Kenmore HE2t | User Guide - Page 9
    B. Water inlet hoses (2) C. Inlet hose washers (4) D. Transit bolt hole plug E. Beaded tie strap Alternate Parts Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the toll-free number on the cover or in the "Assistance or Service
  • Kenmore HE2t | User Guide - Page 10
    • A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs (180 kg). Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. Installation Clearances • The location must be large
  • Kenmore HE2t | User Guide - Page 11
    in 2 * (155 cm2) 3" (7.6 cm) 12" (30.5 cm) 1" (2.5 cm) 24 in.2 (155 cm 2) 1" 29¹⁄4" 4" (2.5 cm) (80 cm) (10.2 cm) A B A. Side view - closet or confined area B. Closet door with vents Recessed or closet installation Washer on pedestal 3" (7.6 cm) 38" min. (96.5 cm) 1" (2.5 cm) 27" (68
  • Kenmore HE2t | User Guide - Page 12
    DRAIN SYSTEM The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See "Tools and Parts." Standpipe drain system - wall or floor (views A & B) The standpipe drain
  • Kenmore HE2t | User Guide - Page 13
    for electric current. This washer is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING: Improper connection
  • Kenmore HE2t | User Guide - Page 14
    in the rear panel of the washer that support the suspension system during transportation. These bolts also retain the power cord inside the washer until the bolts are removed. A B A. Coupling B. Washer Connect the inlet hoses to the water faucets Make sure the washer drum is empty. 1. Attach
  • Kenmore HE2t | User Guide - Page 15
    follow these instructions. Remove drain hose from the washer Gently pull the corrugated drain hose from the shipping clips. Connect the inlet hoses to the washer H C H. Hot water inlet C. Cold water inlet 1. Attach the hot water hose to the washer's hot (H) water inlet valve. Screw on coupling
  • Kenmore HE2t | User Guide - Page 16
    , do not seal the drain hose into the standpipe. LEVEL THE WASHER One foot has been installed at a different height on your new washer. The other three feet were preset at the factory. Properly leveling your washer will minimize excessive noise and vibration. 1. Push on the upper front panel to be
  • Kenmore HE2t | User Guide - Page 17
    . 5. Check that the water faucets are on. 6. Check for leaks around faucets and inlet hoses. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death
  • Kenmore HE2t | User Guide - Page 18
    - NOTES - 2-10
  • Kenmore HE2t | User Guide - Page 19
    conventional washer. ELECTRONIC CONTROLS Flexible electronic controls are easy to use whether you are a beginner or an expert. AUTO WATER LEVEL Adjusting to the size of the load, this feature allows the washer to use the minimal amount of water needed to clean and rinse the clothes. With a low water
  • Kenmore HE2t | User Guide - Page 20
    SMART DISPENSERS The three compartments in the dispenser allow loading of all laundry additives before the washer is started. The additives will be dispensed into the selected. The Detergent Advantage System Dispenser tray is easily removed for cleaning. Use only HE High Efficiency detergent. 3-2
  • Kenmore HE2t | User Guide - Page 21
    risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. The following is a guide to using the washer. Please refer to specific sections of this manual for more detailed information. Do not store laundry products on the top surface of
  • Kenmore HE2t | User Guide - Page 22
    with less water, will create too much sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer errors, longer cycle the front of the tub for small items. 2. Close the washer door by pushing it firmly until the lock clicks. The washer door will remain locked during
  • Kenmore HE2t | User Guide - Page 23
    CYCLE COMPLETE status light illuminates, the door unlocks, and the wash load can be removed from the washer. The washer powers down automatically 5 minutes after the cycle is complete and the CYCLE COMPLETE light goes off. To power down the washer manually after the wash cycle is complete, select
  • Kenmore HE2t | User Guide - Page 24
    to your load. • drain. 4. When the spin is complete, the door unlocks. Items can be removed from the washer. STATUS LIGHTS These lights show which portion of the cycle the washer is operating. They also indicate when you can add an additional item to the wash cycle and when the controls are locked
  • Kenmore HE2t | User Guide - Page 25
    while the washer is operating. To lock the controls Select and hold END OF CYCLE SIGNAL for 3 seconds. The CONTROL LOCKED status light illuminates. Estimated Time Remaining The cycle times vary automatically based on your water pressure, water temperature, detergent, and clothes load. The cycle
  • Kenmore HE2t | User Guide - Page 26
    ) Delicate/ Hand Wash Clean Washer Rinse/Spin Drain/Spin Soak Estimated Time* ( 20°C) 0:14 N/A 0:29 Cold 68°F (20°C) Spin Speed High High High High High Low Low High High No Spin * The cycle times vary automatically based on your water pressure, water temperature, detergent, and clothes load
  • Kenmore HE2t | User Guide - Page 27
    when the door is locked or unlocked, and during the washing, rinsing, or spinning process. Between changes in wash actions, there will be momentary pauses. You will hear water spraying and splashing during the wash and rinse cycles. These new sounds and pauses are part of normal washer operation
  • Kenmore HE2t | User Guide - Page 28
    temperature based on the type of load you are washing. Use the warmest wash water safe for fabrics. Follow garment label instructions. The water temperature for all rinse cycles is cold. Cold rinses save energy. Temperature Guide Wash Water Temperature SUPER HOT HOT WARM COLD Suggested Fabrics
  • Kenmore HE2t | User Guide - Page 29
    GUIDE Refer to the chart below for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these washer cycles. CYCLE SUGGESTED LOAD " Clean Washer No clothes Rinse & Spin All loads Drain & Spin All loads Soak All loads Delay Wash
  • Kenmore HE2t | User Guide - Page 30
    washer door and remove any clothing or items from the washer. 2. Inspect the gray colored seal/bellow between the door opening and the basket for stained areas. Pull back the seal/ bellow to inspect all areas under the seal/bellow and to check for foreign objects. NOTES: • Read these instructions
  • Kenmore HE2t | User Guide - Page 31
    failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear or leaks are found. When replacing your inlet hoses, record the date of replacement. VACATION, STORAGE, & MOVING CARE Install and store your washer where it will not freeze. Because some water may stay in the hoses
  • Kenmore HE2t | User Guide - Page 32
    R.V.-type antifreeze in the drum. Run washer on a Drain/Spin cycle. 2. Unplug the power cord. 3. Disconnect the drain hose from the drain system and attach to rear panel clips. 4. Shut off both water faucets. 5. Disconnect the water inlet hoses from faucets, then drain the hoses and clip them to the
  • Kenmore HE2t | User Guide - Page 33
    below for potential problem and troubleshooting checks. An error code may be shown in the Estimated Time Remaining display (on some models). • "Spin" and "Wash" (HT "Rinse" and "Cycle Complete") illuminated or "F20" on display (Water Inlet Problem-no water or insufficient water supply) Select PAUSE
  • Kenmore HE2t | User Guide - Page 34
    This washer has a tight seal to avoid water leaks. To avoid odors leave the door open to allow the washer to dry between uses. DOOR WON'T UNLOCK • Did all of the water drain out of the washer during the spin? Select DRAIN/SPIN to remove any water remaining in the washer. The washer door will unlock
  • Kenmore HE2t | User Guide - Page 35
    tripped? Replace the fuse, or reset the circuit breaker. • Are both the hot and cold water faucets turned on? Turn on the water. • Is the water inlet hose kinked? Straighten the hoses. • Are the water inlet valve screens clogged? Turn off the water and remove inlet hoses from the washer. Remove any
  • Kenmore HE2t | User Guide - Page 36
    TOO LONG • Estimated cycle time? The cycle times vary automatically based on your water pressure, water temperature, detergent, and clothes load. The cycle time will be extended if oversudsing occurs or the load is unbalanced. The SUDs routine removes extra suds and assures proper rinsing of your
  • Kenmore HE2t | User Guide - Page 37
    or another cycle with a low spin speed to reduce wrinkling. • Did you overload the washer? The wash load must be balanced and not overloaded. Loads should tumble freely during washing. • Was the wash water warm enough to relax wrinkles? If safe for load, use warm or hot wash water. • Are the hot and
  • Kenmore HE2t | User Guide - Page 38
    - NOTES - 3-20
  • Kenmore HE2t | User Guide - Page 39
    This section instructs you on how to service each component inside the Duet Sport™ Front-Loading Automatic Washer. The components and their locations are shown below. COMPONENT LOCATIONS Water Inlet Valve Line Filter Detergent Dispenser Motor & Assembly Pressure Switch Central Control Unit
  • Kenmore HE2t | User Guide - Page 40
    central control unit clips. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove the three T-20
  • Kenmore HE2t | User Guide - Page 41
    Console Screws e) Lift the top edge of the console and unhook it from the holder clips. 6. To remove the touchpad/LED assembly: a) Pull the selector knob off the switch shaft. b) Press the seven console locking tabs, and unsnap the touchpad/LED assembly, then lift the assembly from the console and
  • Kenmore HE2t | User Guide - Page 42
    . Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove the top cover from the washer (see page 4-2 for the procedure). Wire Clamps 6. Pry up on the locking
  • Kenmore HE2t | User Guide - Page 43
    Stripe VCH7 - Water Inlet 4 BU Wires RD Stripe DP2 - Drain Pump 2 BK Wires BK Stripe DL3 - Door Lock 3 BK Wires GN Stripe Board Edge Connectors HE2 - Heater MS2 - Drive Motor WH Stripe IF2 - Line Filter GN Stripe DLS2 - Door Lock Switch BK Stripe CENTRAL CONTROL UNIT Connector Locking Tabs 4-5
  • Kenmore HE2t | User Guide - Page 44
    THE WATER INLET VALVE Lift Locking Tab Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove the
  • Kenmore HE2t | User Guide - Page 45
    Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Wire Connector Pressure Switch 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove the top cover from the
  • Kenmore HE2t | User Guide - Page 46
    the locking arm on the 2-wire connector to disconnect it from the filter. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Line Filter Wire Connectors 1. Unplug washer or disconnect
  • Kenmore HE2t | User Guide - Page 47
    far enough to access the power supply cord on the rear panel. d) Use a pair of pliers and turn the strain relief on the power supply cord 90° in either direction. Align the strain relief key with the slot in the rear panel, and remove the cord from the washer. Power Supply Cord Strain Relief 4-9
  • Kenmore HE2t | User Guide - Page 48
    Support Bracket Screw Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Water Supply Tube 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove
  • Kenmore HE2t | User Guide - Page 49
    lower front access panel, then lower the panel, and remove it. Lower Front Access Panel 13. Pull the bellows off the lip of the front panel, and push the bellows inside the front panel. 14. Remove the two T-20 Torx screws from the door switch assembly. Screws 11. Open the washer door. Door Switch
  • Kenmore HE2t | User Guide - Page 50
    detergent dispenser. 18. Pull back and unhook the tab on the left side of the detergent dispenser from the cabinet side panel slot, then lift the dispenser out of the washer. Side Panel Slot Tube To Dispenser Line Arrow Water Feed Tube Tube To Tub Detergent Dispenser Tab Detergent Dispenser 4-12
  • Kenmore HE2t | User Guide - Page 51
    the locking tabs and remove the two wire connectors from the detergent dispenser motor terminals. NOTE: When you reconnect the wire connectors, make sure to position the connector with the blue stripe on top. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels
  • Kenmore HE2t | User Guide - Page 52
    the washer door. Retaining Wire Tension Spring 7. To remove the door switch assembly: a) Pull the bellows off the lip of the front panel beside the door switch assembly just enough to access the switch assembly. b) Remove the two T-20 Torx screws from the door switch assembly. Bellows Door Switch
  • Kenmore HE2t | User Guide - Page 53
    from the door switch terminals, then remove the assembly. Bellows Retaining Clamp Screw 3 Door Switch Assembly Connectors 8. To remove the bellows: a) Remove the two T-20 Torx screws from the door switch assembly (see the photo in step 7b). b) Remove the front panel from the washer (see steps
  • Kenmore HE2t | User Guide - Page 54
    e) Pull the bellows off the front of the tub. REASSEMBLY NOTE: When you reinstall the bellows, be sure to position the "weep holes" at the bottom, as shown below. Remove Bellows Bellows Weep Holes 4-16
  • Kenmore HE2t | User Guide - Page 55
    the hoses, align their tab(s) with the marks on the drain pump. Pump-To-Tub Hose Tab Arrow Tabs Pump-ToDrain Hose 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove the lower front access panel (see step 10 on page 4-11 for the procedure). 7. Using
  • Kenmore HE2t | User Guide - Page 56
    8. Lift the wire cover on the drain pump, and disconnect the wire connector from the terminals. 9. Remove the wires from the clip, and remove the drain pump from the washer. REASSEMBLY NOTE: When you reinstall the drain pump, make sure that you completely reseat the rubber pad in its chassis floor
  • Kenmore HE2t | User Guide - Page 57
    washer. 3. Remove the lower front access panel (see step 10 on page 4-11 for the procedure). Pressure Hose Tub Clamp Air Trap Drain Pump 4. Using a shallow pan to catch the water, unscrew the filter from the drain pump, and drain the water from the pump. Pump-To-Tub Hose Pump Clamp Drain Pump
  • Kenmore HE2t | User Guide - Page 58
    Turn off the water supply to the washer. 3. Pull the washer away from the wall. 4. Remove the four plastic shipping bolt hole covers. To remove a cover, lift the rounded end to unhook the locking tab from the slot in the chassis, and slide the cover off the rear panel. 5. Remove the hex-head screws
  • Kenmore HE2t | User Guide - Page 59
    10. Disconnect the four wire connectors from the motor control unit and remove the unit. Motor Control Unit Wire Connectors 4-21
  • Kenmore HE2t | User Guide - Page 60
    before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Pull the washer away from the wall. 4. Remove the rear panel from the washer (see page 4-20
  • Kenmore HE2t | User Guide - Page 61
    servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Basket Drive Pulley 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Pull the washer away from the wall. 4. Remove the rear panel from the washer
  • Kenmore HE2t | User Guide - Page 62
    d) Rotate the motor down and pull it toward you so the bracket studs are out of the tub mounting holes, and remove the motor. Drive Motor Studs Drive Motor Drive Motor 4-24
  • Kenmore HE2t | User Guide - Page 63
    the chassis cutout. Locking Tabs Release Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. If you
  • Kenmore HE2t | User Guide - Page 64
    6. Push out on the two locking tabs of the switch holder, rotate the switch in the direction of the arrow, and remove the switch from the holder. Rotate Switch Up Switch Holder Locking Tabs Interlock Switch 4-26
  • Kenmore HE2t | User Guide - Page 65
    and lock the pulley, then remove the 15/16˝ nut from the drive pulley. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water
  • Kenmore HE2t | User Guide - Page 66
    front frame and remove the frame. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Pull the washer
  • Kenmore HE2t | User Guide - Page 67
    10. Remove the bellows from the tub (see pages 4-14 through 4-16 for the procedure). 11. Using a shallow pan to catch the water, unscrew the filter from the drain pump, and drain the water from the pump. 14. Loosen the clamp and remove the vent tube-to-tub end. Vent Tube-To-Tub Drain Pump Filter
  • Kenmore HE2t | User Guide - Page 68
    the shock absorber 90° so that the locking tabs align with the slots in the tub, and remove the shock absorber. Slot Tab Turn Shock Absorber Here Motor Control Unit Wiring Standoffs 21. Remove the four shock absorbers from the tub. To remove a shock absorber: a) Remove the 11/16˝ (17 mm) mounting
  • Kenmore HE2t | User Guide - Page 69
    flat nuts from the tub. Remove Flat Nuts c) Mark the edges of the tub clamps with a pencil to make it easier to reinstall later. d) Use a large flat-blade screwdriver and pry off the tub clamps. Rear Half Of Tub Front Half Of Tub Basket Pencil Marks Screwdriver Tub Clamp Pry Clamp Off
  • Kenmore HE2t | User Guide - Page 70
    Hub Baffle Stops Pry Up Basket Tabs Tub Gasket 25. To replace a basket baffle (see the right column photos): a) Position the basket with the baffle to be removed on top. b) Using a flat-blade screwdriver, pry up on the two basket locking tabs so they are above the baffle stops. c) Reach inside
  • Kenmore HE2t | User Guide - Page 71
    by disconnecting the component connector at the Central Control Unit (CCU). Electrical Shock Hazard Disconnect power before accessing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. INLET VALVE SOLENOIDS COLD HOT Refer to page 4-6 for the
  • Kenmore HE2t | User Guide - Page 72
    Electrical Shock Hazard Disconnect power before accessing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. PRESSURE SWITCH Pin 1 End Hose Inlet Refer to page 4-7 for the procedure for accessing the pressure switch. To check the pressure
  • Kenmore HE2t | User Guide - Page 73
    Hazard Disconnect power before accessing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. LINE FILTER Pins A & B Pins C & D Refer to page 4-8 for the procedure for accessing the line filter. To check the line filter at the component terminals
  • Kenmore HE2t | User Guide - Page 74
    Shock Hazard Disconnect power before accessing. Replace all parts and panels before operating. Failure to do so To check the motor at the component terminals, perform the following steps. 1. Unplug washer or disconnect power. 2. Disconnect the two wire connectors from the motor and switch terminals
  • Kenmore HE2t | User Guide - Page 75
    Disconnect power before accessing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. DOOR SWITCH Door Switch Door Lock/ Unlock Solenoids Refer to page 4-14 for the procedure for accessing the door switch. To check the door switch at the CCU
  • Kenmore HE2t | User Guide - Page 76
    accessing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. DRAIN PUMP Drain Pump Connector To check the drain pump at the CCU, perform the following steps. 1. Unplug washer or disconnect power. 2. Disconnect the drain pump connector DP2
  • Kenmore HE2t | User Guide - Page 77
    Disconnect power before accessing. Replace all parts and panels before operating. Failure to Ω To check the heater at the CCU, perform the following steps. 1. Unplug washer or disconnect power. 2. Disconnect the heater connector HE2 (see page 4-5) from the CCU. 3. Set the ohmmeter to the R X
  • Kenmore HE2t | User Guide - Page 78
    Disconnect power before accessing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. DRIVE MOTOR Pin 1 Drive Motor Connector Refer to page 4-23 for the procedure for accessing the drive motor. 1. Unplug washer or disconnect power. 2. Disconnect
  • Kenmore HE2t | User Guide - Page 79
    DIAGNOSTICS & TROUBLESHOOTING DIAGNOSTICS DIAGNOSTIC GUIDE Before servicing, check the following: • Make sure there is power at the wall outlet. • Has a household fuse blown or circuit breaker tripped? Time delay fuse? • Are both hot and cold water faucets open and water supply hoses unobstructed?
  • Kenmore HE2t | User Guide - Page 80
    the problem, go to step 7. 7. Unplug washer or disconnect power. 8. Replace the pump. Reference Status LEDs chart, page 6-4 Reference Status LEDs chart, page 6-4 Reference Status LEDs chart, page 6-4 DOOR LOCK ERROR After 6 failed attempts to lock the door. Possible Causes/Procedure Door lock
  • Kenmore HE2t | User Guide - Page 81
    servicing. Possible Causes/Procedure 1. Check the drain hose and make sure it is not plugged or kinked. 2. Unplug washer or disconnect power. 3. Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4. Check/clean drain pump filter
  • Kenmore HE2t | User Guide - Page 82
    Central Control Unit (CCU). 4. Check/clean drain pump filter of foreign objects. 5. Plug in washer or reconnect power. 6. Check drain pump. 7. Check the pressure switch. 8. Verify CCU operation by running a Diagnostic Test or any cycle. Some models do not have the display to show the failure codes
  • Kenmore HE2t | User Guide - Page 83
    error codes. Operation modes: • Display the error states that have been recorded by the appliance. • Run through an automated test. • Run loads to assist in diagnosing potentially non-electrical issues. Starting Service History Mode & Diagnostic Test: NOTE: The washer must be empty and the control
  • Kenmore HE2t | User Guide - Page 84
    Sport Whirlpool Duet Sport Ht Rinse/Spin Rinse/Spin Control Action Door locks. Actuators to be Checked Door lock system Clean Washer Delicate Clean Washer Distribution system is set to CLEAN position. Fill by cold water inlet valve (4 liters). Delicate/Hand Wash Distribution system is set
  • Kenmore HE2t | User Guide - Page 85
    cancel out of the Manual Test Mode press PAUSE/CANCEL. MANUAL OVERVIEW TEST PROGRAM Be sure to perform the Diagnostic Tests before replacing the system components. Exit Condition On completion only On key press or if overfill level is detected Control Action Door locks. Distribution system is set
  • Kenmore HE2t | User Guide - Page 86
    3.2k Ω 2.3k Ω 1k Ω Manually Unlocking the Door Lock System 1. Unplug washer or disconnect power. 2. Remove the lower kick panel. 3. Reach up along the inside of the front and locate the bottom of the door switch/lock unit. 4. Located on the bottom of the door switch/ lock unit is a teardrop shaped
  • Kenmore HE2t | User Guide - Page 87
    lift the front tab up and slide the MCU forward. To remove line/interference filter: 1. Unplug washer or disconnect power. 2. Disconnect the three connectors from the line filter and power cord. 3. Remove the two screws which secure the line filter to the top brace. WASHER CARE Cleaning the door seal
  • Kenmore HE2t | User Guide - Page 88
    procedure: 1. Open the washer door and remove any clothing or items from the washer. 2. Be sure the door is closed. 3. in the washer, all cycle lights will flash and the WASH and CONTROLS LOCKED lights will remain lit. The door will unlock. Press PAUSE/CANCEL to cancel the failure code. Then repeat
  • Kenmore HE2t | User Guide - Page 89
    or disconnect power. 5. Check that the drain hose and drain pump filter are clear of foreign objects and not plugged. 6. Plug in washer or reconnect power. 7. Check drain pump. 8. Verify CCU operation by running a Diagnostic Test or any cycle. CONTROL WON'T 1. Press PAUSE/CANCEL on the touchpad
  • Kenmore HE2t | User Guide - Page 90
    that the drain hose and drain pump filter are clear of foreign objects. 6. Plug in washer or reconnect power. 7. Verify CCU operation by running a Diagnostic Test or any cycle. MACHINE VIBRATES 1. Remove shipping system. 2. Check installation. 3. Check leveling feet. INCORRECT WATER TEMPERATURE
  • Kenmore HE2t | User Guide - Page 91
    WIRING DIAGRAMS WASHER N L IF DOOR LOCK/SWITCH DS DLS Lock Unlock IF2 DS2 DL3 DLS2 1 2 12 1 2 3 1 2 DRIVE MOTOR MOTOR CONTROL UNIT (MCU) L2 N1 MS2 1 2 MI3 1 2 3 HEATING ELEMENT DRAIN PUMP INLET VALVES DISPENSER Motor Switch VC VH HE2 21 DP2 1 2 VH7 1 3 DI6 571 3 56 DR1
  • Kenmore HE2t | User Guide - Page 92
    S1 = GND SWITCH - FRONT S2 = GND SWITCH - REAR CABINET S2 MCU POWER CORD REAR BELT: HIGH INSULATED 1M Ω Hub MOTOR GROUNDING SYSTEM WITH HEATER S1 = GND SWITCH - FRONT S2 = GND SWITCH - REAR CABINET S2 MCU 1M Ω Hub HE* * Heating element not present on all models S1 FRONT REAR MOTOR S1
  • Kenmore HE2t | User Guide - Page 93
    - NOTES - 7-3
  • Kenmore HE2t | User Guide - Page 94
    - NOTES - 7-4
  • Kenmore HE2t | User Guide - Page 95
    'S HOME CALL: THE TECHNICAL ASSISTANCE LINE: 1-800-253-2870 HAVE YOUR STORE NUMBER READY TO IDENTIFY YOU AS AN AUTHORIZED SERVICER FOR LITERATURE ORDERS: PHONE: 1-800-851-4605 FOR TECHNICAL INFORMATION AND SERVICE POINTERS: www.servicematters.com IN CANADA: FOR PRODUCT SPECIFICATIONS AND WARRANTY
  • Kenmore HE2t | User Guide - Page 96
    CORPORATION
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
CONSUMER SERVICES TECHNICAL
EDUCATION GROUP PRESENTS
L-78
JOB AID
Part No. 8178558
FRONT-LOADING
AUTOMATIC
WASHER
MODELS: WFW8300SW, WFW8500SW, WFW8500SR