Kenmore HE2t User Guide - Page 68

REASSEMBLY NOTE, To remove the tub and basket - temperature sensor

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

18. Remove the drive motor from the tub (see page 4-23 for the procedure). 19. Remove the temperature sensor and heater from the tub (see page 4-22 for the procedure). 20. Remove the four motor control unit wiring standoffs from the tub. Squeeze in on the standoff tabs to release the standoffs. b) Using a pair of pliers, turn the top of the shock absorber 90° so that the locking tabs align with the slots in the tub, and remove the shock absorber. Slot Tab Turn Shock Absorber Here Motor Control Unit Wiring Standoffs 21. Remove the four shock absorbers from the tub. To remove a shock absorber: a) Remove the 11/16˝ (17 mm) mounting bolt and nut from the base. REASSEMBLY NOTE: When you reinstall the shock absorbers in the base mounting brackets, tighten the nut until it contacts the bracket, then turn the nut an additional 1/4-turn. 22. Remove the end of the vent tube from the tub. 23. To remove the tub and basket: a) Lift the tub and basket assembly and unhook the two suspension springs, then remove the assembly from the washer, and place it front-side down on a padded surface. Remove Vent Tube 11/16˝ (17 mm) Bolt & Nut Unhook Tub Springs 4-30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4-30
18.
Remove the drive motor from the tub (see
page 4-23 for the procedure).
19. Remove the temperature sensor and
heater from the tub (see page 4-22 for
the procedure).
20. Remove the four motor control unit wiring
standoffs from the tub. Squeeze in on the
standoff tabs to release the standoffs.
Motor Control Unit Wiring Standoffs
21. Remove the four shock absorbers from
the tub. To remove a shock absorber:
a) Remove the 11/16
˝
(17 mm) mount-
ing bolt and nut from the base.
b) Using a pair of pliers, turn the top of
the shock absorber 90
°
so that the
locking tabs align with the slots in the
tub, and remove the shock absorber.
11/16
˝
(17 mm)
Bolt & Nut
Tab
Slot
Turn Shock
Absorber Here
REASSEMBLY NOTE:
When you re-
install the shock absorbers in the base
mounting brackets, tighten the nut until it
contacts the bracket, then turn the nut an
additional 1/4-turn.
22. Remove the end of the vent tube from
the tub.
23.
To remove the tub and basket:
a) Lift the tub and basket assembly and
unhook the two suspension springs,
then remove the assembly from the
washer, and place it front-side down
on a padded surface.
Unhook Tub Springs
Remove Vent Tube