Kenmore HE2t User Guide - Page 76

Drain Pump - washer pump

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Electrical Shock Hazard Disconnect power before accessing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. DRAIN PUMP Drain Pump Connector To check the drain pump at the CCU, perform the following steps. 1. Unplug washer or disconnect power. 2. Disconnect the drain pump connector DP2 (see page 4-5) from the CCU. 3. Set the ohmmeter to the R X 1 scale. 4. Touch the ohmmeter test leads to connector pins 1 and 2. The meter should indicate approximately 12.3 Ω. Refer to page 4-17 for the procedure for accessing the drain pump. To check the drain pump at the component terminals, perform the following steps. 1. Unplug washer or disconnect power. 2. Disconnect the wire connector from the drain pump. 3. Set the ohmmeter to the R X 1 scale. 4. Touch the ohmmeter test leads to the drain pump terminals. The meter should indicate approximately 12.3 Ω. Connector DP2 1 2 At CCU 5-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
5-6
Electrical Shock Hazard
Disconnect power before accessing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
DRAIN PUMP
Refer to page 4-17 for the procedure for ac-
cessing the drain pump.
To check the drain pump at the component
terminals, perform the following steps.
1.
Unplug washer or disconnect power.
2.
Disconnect the wire connector from the
drain pump.
3.
Set the ohmmeter to the R X 1 scale.
4.
Touch the ohmmeter test leads to the
drain pump terminals. The meter should
indicate approximately 12.3
Ω
.
To check the drain pump at the CCU, perform
the following steps.
1.
Unplug washer or disconnect power.
2.
Disconnect the drain pump connector
DP2
(see page 4-5) from the CCU.
3.
Set the ohmmeter to the R X 1 scale.
4.
Touch the ohmmeter test leads to con-
nector pins 1 and 2. The meter should
indicate approximately 12.3
Ω
.
Drain Pump
Connector
1
2
Connector DP2
At CCU