Kenmore HE2t User Guide - Page 67

REASSEMBLY NOTE, Continued on the next - pressure switch

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

10. Remove the bellows from the tub (see pages 4-14 through 4-16 for the procedure). 11. Using a shallow pan to catch the water, unscrew the filter from the drain pump, and drain the water from the pump. 14. Loosen the clamp and remove the vent tube-to-tub end. Vent Tube-To-Tub Drain Pump Filter 12. Loosen the clamp and remove the pumpto-tub hose from the drain pump. REASSEMBLY NOTE: When you reconnect the hose, align the tab with the arrow on the drain pump. Pump-To-Tub Hose 15. Remove the basket drive pulley from the basket shaft (see page 4-27 for the procedure). 16. Remove the T-20 Torx screw from the ground wire that is connected to the bearing hub, and pull the wire out of the tub holes. Tab Arrow Ground Wire Screw Bearing Hub 17. Disconnect the pressure hose from the pressure switch. 13. Remove the rear panel (see page 4-20 for the procedure). 4-29 Pressure Switch Pressure Hose Continued on the next page.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4-29
10. Remove the bellows from the tub (see
pages 4-14 through 4-16 for the proce-
dure).
11. Using a shallow pan to catch the water,
unscrew the filter from the drain pump,
and drain the water from the pump.
Drain Pump Filter
12. Loosen the clamp and remove the pump-
to-tub hose from the drain pump.
REASSEMBLY NOTE:
When you reconnect
the hose, align the tab with the arrow on the
drain pump.
Pump-To-Tub Hose
Tab
Arrow
13. Remove the rear panel (see page 4-20
for the procedure).
14. Loosen the clamp and remove the vent
tube-to-tub end.
Vent Tube-To-Tub
17. Disconnect the pressure hose from the
pressure switch.
Pressure Hose
Pressure Switch
15. Remove the basket drive pulley from the
basket shaft (see page 4-27 for the pro-
cedure).
16. Remove the T-20 Torx screw from the
ground wire that is connected to the bear-
ing hub, and pull the wire out of the tub
holes.
Ground Wire Screw
Bearing Hub
Continued on the next page.