Kenmore HE2t User Guide - Page 60

Removing The Temperature Sensor & Heater

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

REMOVING THE TEMPERATURE SENSOR & HEATER b) Loosen the 10 mm nut and pull the temperature sensor out of the heater. 10 mm Nut Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Pull the washer away from the wall. 4. Remove the rear panel from the washer (see page 4-20 for the procedure). Pull Temperature Sensor Out Of Heater 6. To remove the heater: a) Remove the temperature sensor from the heater (see step 5). b) Loosen (do not remove) the 10 mm nut on the heater. c) Disconnect the two wires and the ground connector wire from the heater. Temperature Sensor & Heater Temperature Sensor & Heater 5. To remove the temperature sensor: a) Disconnect the wire connector from the temperature sensor. Heater Wires Ground Wire 10 mm Nut d) Pull the heater out of the tub opening. Heater Temperature Sensor Wire Connector 4-22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4-22
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.
1.
Unplug washer or disconnect power.
2.
Turn off the water supply to the washer.
3.
Pull the washer away from the wall.
4.
Remove the rear panel from the washer
(see page 4-20 for the procedure).
REMOVING THE TEMPERATURE SENSOR & HEATER
5.
To remove the temperature sensor:
a) Disconnect the wire connector from
the temperature sensor.
b) Loosen the 10 mm nut and pull the
temperature sensor out of the heater.
Temperature Sensor & Heater
Temperature Sensor
Wire Connector
6.
To remove the heater:
a) Remove the temperature sensor from
the heater (see step 5).
b) Loosen (do not remove) the 10 mm
nut on the heater.
c) Disconnect the two wires and the ground
connector wire from the heater.
Temperature Sensor & Heater
10 mm Nut
Heater
Wires
Ground Wire
d) Pull the heater out of the tub opening.
Heater
Pull Temperature
Sensor Out Of
Heater
10 mm Nut