Kenmore HE2t User Guide - Page 58

Removing The Motor Control Unit

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

REMOVING THE MOTOR CONTROL UNIT 6. Pull the bottom of the rear panel out, and slide it down so the top edge is out from behind the lip of the upper panel, and remove the rear panel. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Pull the washer away from the wall. 4. Remove the four plastic shipping bolt hole covers. To remove a cover, lift the rounded end to unhook the locking tab from the slot in the chassis, and slide the cover off the rear panel. 5. Remove the hex-head screws (arrows) from the rear panel. Tab Motor Control Unit 7. Pull the hose out of the holders on top of the motor control unit. 8. Remove the wire ties from the cover. 9. Use a flat-blade screwdriver, and pry the locking tab up on the bottom of the motor control unit to release it, then slide the unit forward to release the four tabs from the keyhole slots, and lift the motor control unit from the washer. Pull Hose Out Of Holder Lift Rounded End & Slide Cover Off 4 Shipping Bolt Hole Covers Rear Panel Pull Wire Ties Out Of Cover 4-20 Pry Up Tab To Release

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4-20
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.
1.
Unplug washer or disconnect power.
2.
Turn off the water supply to the washer.
3.
Pull the washer away from the wall.
4.
Remove the four plastic shipping bolt
hole covers. To remove a cover, lift the
rounded end to unhook the locking tab
from the slot in the chassis, and slide the
cover off the rear panel.
5.
Remove the hex-head screws (arrows)
from the rear panel.
REMOVING THE MOTOR CONTROL UNIT
6.
Pull the bottom of the rear panel out, and
slide it down so the top edge is out from
behind the lip of the upper panel, and re-
move the rear panel.
Lift Rounded End
& Slide Cover Off
Tab
4 Shipping Bolt
Hole Covers
Rear Panel
Motor Control Unit
7.
Pull the hose out of the holders on top of
the motor control unit.
8.
Remove the wire ties from the cover.
9.
Use a flat-blade screwdriver, and pry the
locking tab up on the bottom of the motor
control unit to release it, then slide the
unit forward to release the four tabs from
the keyhole slots, and lift the motor con-
trol unit from the washer.
Pry Up Tab
To Release
Pull Hose Out
Of Holder
Pull Wire Ties
Out Of Cover