Kenmore HE2t User Guide - Page 78

Drive Motor, Interlock Switch

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Electrical Shock Hazard Disconnect power before accessing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. DRIVE MOTOR Pin 1 Drive Motor Connector Refer to page 4-23 for the procedure for accessing the drive motor. 1. Unplug washer or disconnect power. 2. Disconnect the 5-wire connector from the drive motor. 3. Set the ohmmeter to the R X 1 scale. 4. Touch the ohmmeter test leads to the following motor pins. For each measurement, the meter should indicate approximately 6 Ω: Pins 1 and 2 Pins 2 and 3 Pins 1 and 3 INTERLOCK SWITCH COM N.C. Actuator Button Refer to page 4-25 for the procedure for accessing an interlock switch. 1. Unplug washer or disconnect power. 2. Disconnect the wire connectors from either of the interlock switch terminals. 3. Set the ohmmeter to the R X 1 scale. 4. Touch the ohmmeter test leads to the two interlock switch terminals. The meter should indicate an open circuit with the actuator button pushed in, and a closed circuit (0 Ω) with the actuator button out. 5-8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
5-8
Electrical Shock Hazard
Disconnect power before accessing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
DRIVE MOTOR
Refer to page 4-23 for the procedure for ac-
cessing the drive motor.
1.
Unplug washer or disconnect power.
2.
Disconnect the 5-wire connector from the
drive motor.
3.
Set the ohmmeter to the R X 1 scale.
4.
Touch the ohmmeter test leads to the
following motor pins. For each measure-
ment, the meter should indicate approxi-
mately 6
Ω
:
Pins 1 and 2
Pins 2 and 3
Pins 1 and 3
Drive Motor
Connector
Pin 1
INTERLOCK SWITCH
Refer to page 4-25 for the procedure for ac-
cessing an interlock switch.
1.
Unplug washer or disconnect power.
2.
Disconnect the wire connectors from ei-
ther of the interlock switch terminals.
3.
Set the ohmmeter to the R X 1 scale.
4.
Touch the ohmmeter test leads to the
two interlock switch terminals. The meter
should indicate an open circuit with the
actuator button pushed in, and a closed
circuit (0
Ω
) with the actuator button out.
Actuator Button
COM
N.C.