Kenmore HE2t User Guide - Page 52

Removing The Door Switch Assembly, And The Bellows

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

REMOVING THE DOOR SWITCH ASSEMBLY AND THE BELLOWS 6. Using a small screwdriver or a pair of long-nosed pliers, pull the tension spring on the retaining wire out from around the front of the bellows, and remove the wire. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Unplug washer or disconnect power. 2. Turn off the water supply to the washer. 3. Remove the top cover and the console (see page 4-2 for the procedures). 4. Remove the lower front access panel (see step 10 on page 4-11 for the procedure). 5. Open the washer door. Retaining Wire Tension Spring 7. To remove the door switch assembly: a) Pull the bellows off the lip of the front panel beside the door switch assembly just enough to access the switch assembly. b) Remove the two T-20 Torx screws from the door switch assembly. Bellows Door Switch Assembly Screws Retaining Wire Door Switch Assembly Pull Bellows Off Lip Of Panel 4-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4-14
7.
To remove the door switch assembly:
a) Pull the bellows off the lip of the front
panel beside the door switch assem-
bly just enough to access the switch
assembly.
b) Remove the two T-20 Torx screws
from the door switch assembly.
Door Switch
Assembly Screws
Pull Bellows
Off Lip Of
Panel
REMOVING THE DOOR SWITCH ASSEMBLY
AND THE BELLOWS
1.
Unplug washer or disconnect power.
2.
Turn off the water supply to the washer.
3.
Remove the top cover and the console
(see page 4-2 for the procedures).
4.
Remove the lower front access panel
(see step 10 on page 4-11 for the proce-
dure).
5.
Open the washer door.
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.
6.
Using a small screwdriver or a pair of
long-nosed pliers, pull the tension spring
on the retaining wire out from around
the front of the bellows, and remove the
wire.
Bellows
Door Switch
Assembly
Retaining Wire
Tension Spring
Retaining Wire