Kenmore HE2t User Guide - Page 75

Door Switch - washer door locked

Get Kenmore HE2t - 3.7 cu. Ft. Front Load Washer PDF manuals and user guides View all Kenmore HE2t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Electrical Shock Hazard Disconnect power before accessing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. DOOR SWITCH Door Switch Door Lock/ Unlock Solenoids Refer to page 4-14 for the procedure for accessing the door switch. To check the door switch at the CCU, perform the following steps. 1. Unplug washer or disconnect power. 2. Disconnect the door lock/unlock sole- noids connector DL3 (see page 4-5) from the CCU. 3. Set the ohmmeter to the R X 1 scale. 4. To test the door lock/unlock solenoids, touch the ohmmeter test leads to the indicated pins on connector DL3. The meter should indicate as follows: Door Unlock Solenoid - Pins 2 & 3 = 60 Ω Door Lock Solenoid - Pins 1 & 3 = 60 Ω 5. Disconnect the door switch connector DS2 (see page 4-5) from the CCU. 6. To test the door switch, touch the ohmmeter test leads to pins 3 and 1 at DS2. The meter should indicate as follows: Door Closed = 0 Ω Door Open = infinite 1 2 3 1 2 3 1 2 3 Unlock Sol. Lock Sol. Connector DL3 At CCU Door Sw. Connector DS2 At CCU 5-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
5-5
Electrical Shock Hazard
Disconnect power before accessing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
DOOR SWITCH
3.
Set the ohmmeter to the R X 1 scale.
4.
To test the door lock/unlock sole-
noids,
touch the ohmmeter test leads to
the indicated pins on connector
DL3
. The
meter should indicate as follows:
Door Unlock Solenoid - Pins 2 & 3 = 60
Ω
Door Lock Solenoid - Pins 1 & 3 = 60
Ω
5.
Disconnect the door switch connector
DS2
(see page 4-5) from the CCU.
6.
To test the door switch,
touch the ohm-
meter test leads to pins 3 and 1 at
DS2
.
The meter should indicate as follows:
Door Closed = 0
Ω
Door Open = infinite
Door Lock/
Unlock
Solenoids
Door Switch
1
2
3
1
2
3
1
2
3
Door Sw.
Lock Sol.
Unlock Sol.
Connector DS2
At CCU
Connector DL3
At CCU
Refer to page 4-14 for the procedure for ac-
cessing the door switch.
To check the door switch at the CCU, perform
the following steps.
1.
Unplug washer or disconnect power.
2.
Disconnect the door lock/unlock sole-
noids connector
DL3
(see page 4-5) from
the CCU.