Home » Konica Minolta Manuals » Printers » Konica Minolta bizhub PRESS C71hc » Manual Viewer

Konica Minolta bizhub PRESS C71hc SD-513 User Manual - Page 173

Tri-Fold Crease Position

View all Konica Minolta bizhub PRESS C71hc manuals

Add to My Manuals
Save this manual to your list of manuals

Page 173 highlights

5 [Saddle Stitcher Adjustment] - [Crease Position Adjustment] 5.12 5.12.2 Tri-Fold Crease Position The tri-fold crease position determined by Creaser Unit CR-101 mounted on Saddle Stitcher SD-513 can be moved. The position of 1st Fold Crease is calculated from the edge of the sheet, while that of 2nd Fold Crease is calculated from the position of 1st Fold Crease. Adjust the distance between each reference position and the crease position. Objects of adjustment: Full Area (Offset for All Size), A4 w, 8.5 e 11 w NOTICE With [Full Area] ([Offset for All Size]) selected, the entered value will be applied to all sizes. With a specific paper size selected, set value will be the sum of the entered value and the value previously specified for [Full Area] ([Offset for All Size]). NOTICE Make this adjustment after [Tri-Fold Position Adj.] (page 5-28) has been completed. NOTICE Depending on the paper weight, when the crease position is adjusted, it may no longer align with the fold position. In such a case, make this adjustment again so that the crease position aligns with the fold position. NOTICE Depending on the crease position, the tri-fold position is drawn to the crease position, and the fold position may be changed. In this case, carry out [Tri-Fold Position Adj.] (page 5-28) to determine the tri-fold position, then follow the steps below to adjust the crease position. 1. Move the crease position away from the tri-fold position. Move the crease position in the minus (-) or plus (+) direction so that each current position is displaced at a maximum before outputting sheets. 2. Check the output sheets, then measure the distance between the output crease position and the desired crease position. 3. Enter the distance measured above into the Setting Data field of Crease Position Adjustment. See the steps below for details on the setting procedure. 5-44 1 Press [Adjustment] on the Machine Screen to display the Adjustment Menu Screen. Saddle Stitcher SD-513

Section	Page
Table of contents	2
1 Introduction	7
1.1 Intended Use of this Machine	7
1.2 Users of this Machine	8
1.3 Objectives of this Manual	9
2 Preparation for Use	11
2.1 Machine Configuration	11
2.2 Warning Label and Caution Label	16
2.3 Optional Devices	20
2.4 Paper Information	21
2.4.1 Available Paper Weights	21
2.4.2 Exit Tray Capacity	22
2.4.3 Paper Size	26
2.5 Machine Screen	27
2.5.1 Screen with SD-513 installed	27
2.5.2 Setting Screen with SD-513 installed	28
3 Supplies and Disposals	31
3.1 Replenishing Staple Supply	31
3.1.1 Replenishing Staple Supply in Saddle Stitcher SD-513	31
3.2 Disposing Trimmings	33
3.2.1 Emptying Trim Scrap Box of Saddle Stitcher SD-513	33
3.2.2 Emptying Slit Scrap Box of Saddle Stitcher SD-513	35
4 Using Saddle Stitcher SD-513	39
4.1 Basic Functions of Saddle Stitcher SD-513	39
4.2 Additional Functions of Saddle Stitcher SD-513	42
4.2.1 Creaser Unit CR-101	42
4.2.2 Trimmer Unit TU-503	47
4.2.3 Combination of Creaser Unit CR-101 and Trimmer Unit TU-503	52
4.2.4 Folding Unit FD-504	56
4.2.5 Combination of Basic Functions and Additional Functions	58
4.3 Making Folded Booklets: Fold & Staple/Multi Half-Fold	59
4.3.1 Functional Overview	59
4.3.2 Settings on the Copy Screen	60
4.3.3 Settings in Printer Driver	63
4.4 Folding Copies in Three: Multi Tri-Fold	64
4.4.1 Functional Overview	64
4.4.2 Settings on the Copy Screen	65
4.4.3 Settings in Printer Driver	66
4.5 Adding Fold Lines (Creases) on Paper	67
4.5.1 Functional Overview	67
4.5.2 Settings on the Copy Screen	69
4.5.3 Settings in Printer Driver	72
4.6 Adding Fold Lines (Creases) for Fold & Stapled/Multi Half-Folded Cover	73
4.6.1 Functional Overview	73
4.6.2 Settings on the Copy Screen	74
4.6.3 Settings in Printer Driver	78
4.7 Adding Fold Lines (Creases) for Multi Tri-Folded Paper	79
4.7.1 Functional Overview	79
4.7.2 Settings on the Copy Screen	80
4.7.3 Settings in Printer Driver	81
4.8 Performing 2-Side Slitting	82
4.8.1 Functional Overview	82
4.8.2 Settings on the Copy Screen	83
4.8.3 Settings in Printer Driver	84
4.9 Performing 2-Side Slitting on Fold & Stapled/Multi Half-Folded Paper	85
4.9.1 Functional Overview	85
4.9.2 Settings on the Copy Screen	87
4.9.3 Settings in Printer Driver	92
4.10 Performing 2-Side Slitting on Multi Tri-Folded Paper	93
4.10.1 Functional Overview	93
4.10.2 Settings on the Copy Screen	94
4.10.3 Settings in Printer Driver	96
4.11 Forming Spine Corners on Fold & Stapled Sets	97
4.11.1 Functional Overview	97
4.11.2 Settings on the Copy Screen	98
4.11.3 Settings in Printer Driver	101
4.12 Manually Using Folding Unit FD-503 or Saddle Stitcher SD-513	102
4.13 Combining Perfect Binder PB-503	105
4.13.1 Making Perfect-Bound Booklets	105
4.14 Functions of Printer Driver	110
4.14.1 PS Plug-in driver (Windows/Mac OS X)	110
4.14.2 PPD driver (Windows)	117
4.14.3 PPD Driver (Mac OS X)	119
4.14.4 PCL driver (Windows)	121
4.15 Job Operations	128
4.15.1 Operating Prior Print	128
4.15.2 Printing a Sample during Output and Checking it: Sample Print	128
5 Various Settings and Adjustment	131
5.1 Tray Setting	131
5.1.1 PI-PFU Tray Setting (bizhub PRESS 1250/1250P/1052)	131
5.1.2 Tray Setting for PI Trays: Post Inserter of Folding Unit FD-503	138
5.2 [Saddle Stitcher Adjustment] - [Staple Center Adjustment]	145
5.2.1 Center Position of 2 Position Staples	145
5.2.2 Center Position of Front 2 Positions of 4 Position Staple	146
5.2.3 Center Position of Rear 2 Positions of 4 Position Staple	148
5.3 [Saddle Stitcher Adjustment] - [Staple Paper Width Adj.]	150
5.4 [Saddle Stitcher Adjustment] - [Staple Pitch Adjustment]	152
5.4.1 Staple Pitch of 2 Position Staple	152
5.4.2 Staple Pitch of Front 2 Positions of 4 Position Staple	153
5.4.3 Staple Pitch of Rear 2 Positions of 4 Position Staple	155
5.5 [Saddle Stitcher Adjustment] - [Tri-Fold Position Adj.]	157
5.6 [Saddle Stitcher Adjustment] - [Fold Skew Adjustment]	159
5.7 [Saddle Stitcher Adjustment] - [Half-Fold Position Adjustment]	161
5.8 [Saddle Stitcher Adjustment] - [Fold Paper Width Adjustment]	163
5.9 [Saddle Stitcher Adjustment] - [Fore-edge Trimming Adjustment]	165
5.10 [Saddle Stitcher Adjustment] - [Parallel Trimming Adjustment]	167
5.11 [Saddle Stitcher Adjustment] - [2-Side Slitting Adjustment]	169
5.12 [Saddle Stitcher Adjustment] - [Crease Position Adjustment]	171
5.12.1 Half-Fold Crease Position	171
5.12.2 Tri-Fold Crease Position	173
5.12.3 Perfect Bind Cover Crease Position	175
5.13 [Saddle Stitcher Adjustment] - [Flattening a Fold (Strength)]	177
5.14 [Saddle Stitcher Adjustment] - [Flattening a Fold (Frequency)]	178
5.15 [Saddle Stitcher Adjustment] - [Staple Offset Adjustment]	179
5.16 [Saddle Stitcher Adjustment] - [Staple Tip Adjustment]	180
5.17 [Saddle Stitcher Adjustment] - [2-Side Slitting Finishing Adj.]	181
5.18 [Saddle Stitcher Adjustment] - [Trimmer Receiver Adjustment]	182
5.18.1 Count Select for Move	182
5.18.2 Moving Pitch Select	183
5.18.3 Forcibly Move	184
6 Troubleshooting	187
6.1 If [Mishandled paper] Message Is Displayed	187
6.1.1 Precautions for Removing Mishandled Paper from Saddle Stitcher SD-513	187
6.2 Troubleshooting Tips	188
7 Cleaning	191
7.1 Cleaning the conveyance belt of the bundle exit tray	191
8 Appendix	195
8.1 Typical Specifications	195
8.1.1 Saddle Stitcher SD-513	195
8.1.2 Creaser Unit CR-101 (equipped in Saddle Stitcher SD-513)	197
8.1.3 Trimmer Unit TU-503 (equipped in Saddle Stitcher SD-513)	198

Match case Limit results 1 per page

5-44

Saddle Stitcher SD-513

[Saddle Stitcher Adjustment] - [Crease Position Adjustment]

5.12

5.12.2

Tri-Fold Crease Position

The tri-fold crease position determined by

Creaser Unit CR-101

mounted on

Saddle Stitcher SD-513

can

be moved. The position of 1st Fold Crease is calculated from the edge of the sheet, while that of 2nd Fold

Crease is calculated from the position of 1st Fold Crease. Adjust the distance between each reference posi-

tion and the crease position.

Objects of adjustment: Full Area (Offset for All Size), A4

, 8.5

NOTICE

With [Full Area] ([Offset for All Size]) selected, the entered value will be applied to all sizes. With a specific pa-

per size selected, set value will be the sum of the entered value and the value previously specified for [Full

Area] ([Offset for All Size]).

NOTICE

Make this adjustment after [Tri-Fold Position Adj.] (page 5-28) has been completed.

NOTICE

Depending on the paper weight, when the crease position is adjusted, it may no longer align with the fold po-

sition. In such a case, make this adjustment again so that the crease position aligns with the fold position.

NOTICE

Depending on the crease position, the tri-fold position is drawn to the crease position, and the fold position

may be changed.

In this case, carry out [Tri-Fold Position Adj.] (page 5-28) to determine the tri-fold position, then follow the

steps below to adjust the crease position.

1. Move the crease position away from the tri-fold position. Move the crease position in the minus (-) or plus

(+) direction so that each current position is displaced at a maximum before outputting sheets.

2. Check the output sheets, then measure the distance between the output crease position and the desired

crease position.

3. Enter the distance measured above into the Setting Data field of Crease Position Adjustment.

See the steps below for details on the setting procedure.

Press [Adjustment] on the Machine Screen to display the Adjustment Menu Screen.