Kyocera ECOSYS P6030cdn ECOSYS P6030cdn Operation Guide (Advanced)
Kyocera ECOSYS P6030cdn Manual
View all Kyocera ECOSYS P6030cdn manuals
Add to My Manuals
Save this manual to your list of manuals |
Kyocera ECOSYS P6030cdn manual content summary:
- Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 1
PRINT ECOSYS P6030cdn ADVANCED OPERATION GUIDE - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 2
- Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 3
Paper 1-4 Special Paper 1-7 Paper Type 1-13 Loading Paper 1-14 2 Using the Operation Panel General Information 2-2 Understanding the Operation Panel 2-3 Keys 2-6 Using the Menu Selection System 2-8 Setting a Mode settings 2-94 Adjust/Maintenance (Adjust/Maintenance selection/setting) 2-97 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 4
iv - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 5
INTRODUCTION This guide has the following chapters: 1 Handling Paper Explains how choose, handle and load paper. 2 Using the Operation Panel Explains how to use the operation panel to configure the printer. 3 Options Shows the available options. 4 Computer Interface Describes the possible - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 6
manual uses the following conventions: Description Example Used to emphasize a key word, phrase or reference to additional information. Used to denote buttons on the software. To replace the toner container, refer to Toner important information. IMPORTANT Ensure paper is not folded, curled, - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 7
1 Handling Paper This chapter contains explanations on the following topics: General Guidelines Selecting the Right Paper Paper Type Loading Paper 1-2 1-4 1-13 1-14 Handling Paper 1-1 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 8
paper jams and other problems, and the higher the level of quality your printed output will reflect. Differences between paper from different suppliers can also affect the machine's performance. A high-quality printer cannot produce highquality results when the wrong paper is used. Low-priced paper - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 9
inches Minimum and Maximum Paper Sizes The minimum and maximum paper sizes are as follows. For non standard paper such as transparency, labels, vellum, cardstock, envelope, and coated, the MP (Multi-Purpose) tray must be used. Paper Cassette MP Tray Minimum Paper Size Minimum Paper Size 138 mm - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 10
paper. Condition Avoid using paper that is bent at the edges, curled, dirty, torn, embossed, or contaminated with lint, clay, or paper shreds. Use of paper in these conditions can lead to illegible printing and paper jams ISO A6 105 × 148 mm 128 × 182 mm Envelope C5 162 × 229 mm 100 × 148 mm - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 11
or too light may cause feed errors or paper jams as well as premature wear of the product. Uneven weight of paper, namely uneven paper thickness may cause multiple-sheet feeding or print quality problems such as blurring because of poor toner fusing. The recommended basis weight is: Cassette: 60 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 12
be neither extremely thick nor extremely thin. If you are having problems with paper jams, multiple feeds, and faint printing, the paper you are using may be too thin. If you are having problems with paper jams and blurred printing the paper may be too thick. The correct thickness is 0.086 to 0.110 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 13
that is sold specifically for use with copiers or printers (heatfusing type). When using transparencies, labels, thin paper, envelopes, postcards, or thick paper, feed the paper from the MP tray. For details, refer to Paper Source (Selecting the paper feed source) on page 2-37. Since the composition - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 14
90° ±0.2° To prevent printing problems, feed transparencies into the printer one sheet at a time from the MP tray. Always load the transparencies vertically (with the long edge towards the printer). If the transparencies have rough edges on the back, it may cause a paper jam. Remove the rough edges - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 15
contact with any part of the machine. Adhesive paper sticking to the drum or rollers will damage the machine. Label paper has a structure comprising in between are liable to peel off, causing serious paper jam problems. Some label paper is manufactured with an extra margin of top sheet around - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 16
may cause paper jams. Some postcards have rough edges on the back (those are created when the paper is cut). In this case, put the postcards on a flat place and rub the edges with, for example, a ruler to smooth them. Rough Edge Rough Edge Envelopes Slide the envelope switch to envelope mode and - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 17
place and rub the edges once or twice with, for example, a ruler to smooth them. Feeding rough edged paper may cause paper jams. Note If the paper jams even after you smooth it out, load the paper in the MP tray with the leading edge raised up a few millimeters as shown in the illustration. If you - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 18
sheets to stick together when they are fed into the printer. Paper Type Indicators (Optional paper feeder PF-510) If you are going to load non standard paper in the optional paper feeder PF-510, cut out the blank section of the attached paper type indicator sheet, fold the remaining sheet in half - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 19
paper being used. Setting the paper type for the paper source from the printer's operation panel will cause the printer to automatically select the paper source and print in the mode best suited to that type of paper. A different paper Yes Yes Normal 2 Yes Yes ENVELOPE Yes No Heavy 2 No Yes - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 20
a level surface to avoid media jams or skewed printing. Paper Cassette 2 Pull the paper cassette all the way out of the printer. Paper Size Dial 3 Turn the paper size dial so that the size of the paper you are going to use appears in the paper size window. Note When the paper size dial is set to - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 21
5 Pull the release lever and slide the paper stopper to the desired paper size. When using non-standard size paper, move the paper guides and paper stopper all the way out, insert the paper, then adjust the paper guides and paper stopper to the size of the paper. Adjust them so that they are in - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 22
the slot in the printer. Push it straight in as far as it will go. There is a paper gauge on the right side of the front of the paper cassette to indicate the remaining paper supply. When paper is exhausted, the pointer will go down to the level of (empty). Paper Gauge Loading Paper into the MP - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 23
MP tray paper size on the printer's operation panel. Refer to MP Tray Size (Setting MP tray paper size) on page 2-29. 7 Set the appropriate print mode for the paper thickness (envelopes or plain paper). To print on envelopes, slide the envelope switch to the right to select envelope mode. To print - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 24
Paper stopper Align the paper stopper to the desired paper size. • For A4 or Letter size paper : Align with position . • For Legal size paper : Align with position . 1-18 Handling Paper - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 25
Using the Menu Selection System 2-8 Setting a Mode Selection Menu 2-10 Report Print 2-11 USB 2-22 Counter (Viewing the counter value) 2-28 Paper Settings 2-29 Print Settings 2-37 Network (Network settings settings) 2-94 Adjust/Maintenance (Adjust/Maintenance selection/ setting) 2-97 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 26
Information This chapter provides the information you need to configure the Ecosys Color printer. In general you need to use the operation panel only to make default settings. You can make most changes to the printer settings using the printer driver through the application software. Note Changes to - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 27
the Operation Panel The operation panel on the top of the printer has a 2-line by 21-character liquid crystal display (LCD), are displayed during normal operation. • Error codes, when the printer requires the operator's attention; as explained in the Operation Guide. Using the Operation Panel 2-3 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 28
Self test Please wait Please wait (Paper loading) Please wait (Adding toner) Please wait (Calibrating) Please wait (Cleaning) Please wait (Cooling) Ready Processing Low Power Sleeping Canceling data Status Information Meaning The printer is performing self-diagnostics after power-up. The printer is - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 29
starts, or that data is being written to or read from a SSD. Flashing. Indicates that the printer requires maintenance or is warming up. On. Indicates the occurrence of a problem or an error. For details, refer to the Troubleshooting section in the Operation Guide. Using the Operation Panel 2-5 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 30
environment of the printer. Arrow Keys • The four arrow keys are used in the menu system to access an item or enter numeric values. Use and to change menus, and and to move to the sub menu. • The arrow key with the question mark ( ) may be pressed when the paper jam message has - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 31
alternative? is shown in the message display, use and key to select an alternative paper source. OK Key This key is used to: • Finalize settings of numeric values and other selections. • Set the paper source when Use alternative? is shown in the message display. Using the Operation Panel 2-7 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 32
. Settings can be made when Ready is indicated on the printer message display. Note Settings that are received from application software and the printer driver will take priority over settings made in the operation panel. Entering the Mode Selection Menu Press [MENU] when Ready is indicated on the - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 33
Paper Settings Selecting a Menu The mode selection menu is hierarchical. Press or to display the to go back. Indicates that this is the sub-menu Indicates that there is another sub-menu >>Paper Weight Normal 1 Indicates that this is the second sub-menu >> is displayed before the second sub - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 34
Print • USB Memory • Custom Box • Job Box • Counter • Paper Settings • Print Settings • Network • Optional Network • Device Common • Security • Job Accounting • Administrator • Adjust/Maintenance Note If you use the mode first selected when the printer is turned on, Report Print is displayed. For - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 35
> appears. > >Print Menu Map ? Note that menus shown in the list may vary depending on which optional units installed in the printer. Print Menu Map The printer prints a full list of the menu selection system menu map. 1 Press while Report Print > is displayed. 2 >Print Menu Map appears. In - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 36
Menu Map Sample Menu Map Printer Firmware version 2-12 Using the Operation Panel - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 37
Print Status Page You can check the printer's current status, including available memory [OK] again. The message Processing appears and the printer prints a status page. For a sample status page and the printer's firmware version. Status Page Printer Firmware version 1 Paper Settings Interface - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 38
KPDL (AUTO) emulation is set as default when the printer is shipped from the factory. The emulations are: - PCL 6 - KPDL - KPDL (AUTO) 8 Page Information This item shows the page related items: - Total printed page count - Total page count of each paper size 9 Consumable Status This item shows the - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 39
list of the files on the RAM disk. IMPORTANT This is displayed when RAM disk mode is enabled. 1 Press while Report Print > is displayed. 2 Press list of the files on the SSD. IMPORTANT This is only displayed when the printer has a SSD installed and the disk is correctly formatted. 1 Press while - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 40
Print File (Printing a file) Copies (Number of copies) Paper Source (Selecting the paper feed source) • Remove Device (Removing the USB memory) • in the list may vary depending on which optional units installed in the printer. Print File (Printing a file) You can use this to specify printing - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 41
and or and repeatedly until the paper source appears. (For example : Cassette 2) Note that menus shown in the list may vary depending on which optional units installed in the printer. 2 Press [OK]. The message Processing appears and the printer prints a file stored in a USB memory. Remove - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 42
For more information, refer to the Command Center RX User Guide and Printer Driver User Guide. Use the printer's operation panel to print the print data stored in a you have set a password for the Custom Box, carry out the Box Password (Box password input) step next. 2-18 Using the Operation Panel - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 43
password for the box. The password is specified from the printer driver. 1 If you have set a password for the Custom Box, press while >Select Box > is displayed. Box Password screen for selecting the paper source appears. Press or repeatedly until the desired paper source is displayed. - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 44
. Depending on the installed optional units, one or more of the following are displayed: MP tray Cassette (only the printer's standard cassette used) Cassette 1 to 4 (optional paper feeder installed) Auto 5 Press [OK]. The screen for choosing whether to delete the data after printing appears with - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 45
>Select Box 0001:Box 1 Delete All Files (Deletes all the data) Use this procedure to delete all the documents in the Custom Box. 1 Press while >Select Box > and the box number and box name > are displayed. >>Delete All Files ? Press or until >>Delete All Files, and press [OK]. A - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 46
printer driver. Refer to Printer Driver User Guide for the driver settings. Job Retention Job Retention has four modes as summarized below. These modes are selected from the printer driver capacity PIN security Data after printing Data at power off SSD No Stored Deleted Necessary No Stored - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 47
data) (Data Name) ID (number of copies) (Input passwords) (Data Name) Copies (number of copies) (Number of installed in the printer. Quick Copy (Using Quick Copy) This mode enables you to printer operation panel. To print a job as a quick copy job, refer to Printer Driver User Guide. The default - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 48
and-Hold When you print multiple copies, this mode first prints one copy so that you can the remaining copies, wastage of paper can be reduced. The printer prints one copy and, at the printer is turned off, all stored jobs will be deleted. Note Refer to Printer Driver User Guide for the driver - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 49
print job. In the stored job mode, access codes are not mandatory, but can be set on the printer driver if printing with PIN security is Print data will be stored in the SSD after printing. Refer to Printer Driver User Guide for the driver settings. Releasing a Private/Stored Job 1 Press while Job - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 50
OK]. The ID input line appears. Enter the four-digit access code entered in the printer driver and press [OK]. To enter the ID, press or to move the Jobs saved using Private Print will be automatically deleted if you turn the power off after printing, but jobs saved using Stored Job will not be - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 51
Configuration >>Delete ? Off Changing the Maximum Number of Quick Copy This changes maximum number of Quick Copy from 0 to 50. The default is 32. 1 Press while Job Box > is displayed. 2 Press or repeatedly until >Job Box Configuration > > appears. 3 Press . 4 Press or repeatedly - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 52
Counter Counter (Viewing the counter value) Displays the number of pages printed. The options available in Counter are as follows: • Printed Pages (Displaying the total printed pages) • Color (Displaying the color printed pages) • Black & White (Displaying the Black & White printed pages) 1 Press [ - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 53
cause paper jam. 1 Press while Paper Settings > is displayed. 2 Press or repeatedly until >MP Tray Size appears. 3 Press [OK]. A blinking question mark (?) appears. 4 Press or to display the desired paper size. The message display toggles through the following paper sizes: Envelope Monarch - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 54
tray paper type) You can use this to set the paper type that can be supplied from the MP tray. The default setting is PLAIN. For more information about paper types ENVELOPE CARDSTOCK COATED THICK HIGH QUALITY CUSTOM 1 (to 8) Note You can define any paper type and store that definition in the printer - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 55
installed, use the same procedure to load paper into the paper feeder cassettes. 1 Pull the cassette out of the printer and set the paper size using the paper size dial. A4 Paper Size Dial >Cassette Size > ? Custom Using the Operation Panel 2 Adjust the paper guides in the cassette to the size of - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 56
Envelope Monarch, Envelope #10, Envelope #9, Envelope #6, Envelope DL, OufukuHagaki, Youkei 2 and Youkei 4 are displayed when one of cassettes 2 to 4 in the optional paper and inches. The current unit of measurement is displayed (the default setting is mm). 3 Press [OK]. A blinking question mark - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 57
(plain, recycled, etc.) for the paper cassette, you can automatically select the paper in the paper cassette according to the paper type you command on the printer driver. The default setting is plain paper for all paper cassettes. If the PF-500 or PF-510 optional paper feeder is installed, use the - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 58
COATED THICK HIGH QUALITY CUSTOM 1 (to 8) IMPORTANT LABELS, ENVELOPE, CARDSTOCK and COATED will only appear when the optional paper feeder PF-510 is installed. Note You can define any paper type and store that definition in the printer. For more information, refer to Type Adjust (Creating custom - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 59
ENVELOPE CARDSTOCK COATED THICK HIGH QUALITY CUSTOM 1 (to 8) 5 Press [OK]. 6 Press and proceed to the next step Paper Weight (Setting the paper weight). Paper Weight (Setting the paper weight) You can set the paper thickness for your custom paper type to be customized. The default setting - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 60
For details of the default setting for each paper type, refer to Paper Specifications on page 1-2. 5 Press [OK]. 6 Press [MENU]. The display returns to Ready. The custom paper type setting is completed. Reset Type Adjust (Resetting the custom paper type) Reset all the custom paper type that was set - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 61
display settings) 1 Press [MENU]. 2 Press or repeatedly until Print Settings > appears. > Paper Source (Selecting the paper feed source) You can select the paper source, from which the printer feeds paper as the default. If an optional paper feeder(s) is installed, it is also available for the - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 62
to the Command Center RX User Guide. Paper Feed Mode (Setting the paper feed source) This mode specifies how the paper should be fed once the paper feed source and paper type have been chosen. If Auto is selected, the printer searches for a paper feed source that matches the paper size and type, and - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 63
either short edge or long edge binding mode. Note Duplex printing can be also performed from the MP tray. If the paper to be fed from the MP tray does not match the paper size and paper type of the current paper feed source cassette, a paper jam may occur. IMPORTANT Duplex printing for coated - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 64
>Duplex ? Off Binding Modes Binding refers to the manner in which printed pages of paper are joined together (by (?) appears. 4 Press or to display the desired binding mode. The message display toggles through the following: Off (default) Short edge bind Long edge bind 5 Press [OK]. 6 Press - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 65
printer ignores the difference between A4 and Letter paper sizes. Printing is performed without an error message even if the actual paper size in the current cassette differs from the paper size formatting the job. By default . One of the emulation modes appears, indicating the emulation currently - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 66
and TRANSPARENCY is selected as the paper type setting. IMPORTANT Depending on the paper used, printing in gloss mode may cause wrinkle in paper. To reduce wrinkle, try using thicker paper. Use the procedure below to select Gloss mode. The default setting is Low. 2-42 Using the Operation Panel - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 67
of toner used during printing. Because images printed in this mode may be slightly coarser than those printed in standard resolution, you should use EcoPrint for test prints or other situations where high-quality prints are not required. Use the procedure below to select EcoPrint mode. The default - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 68
>>Copies 001 1 Press or repeatedly until >>Copies appears. 2 Press [OK]. A blinking cursor (_) appears. 3 Press or to increase or decrease, respectively, the value at the blinking cursor. The number of copies can be set between 1 and 999. Use and to move the cursor right and left. 4 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 69
Press [MENU]. The display returns to Ready. TIFF/JPEG Size (Print mode setting for TIFF/JPEG files) Use this setting to select the printing method used when TIFF or JPEG files are printed directly. The default setting is Paper Size. 1 Press while >Page Set > is displayed. 2 Press or repeatedly - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 70
[OK]. A blinking question mark (?) appears. 4 Press or to display the job name to be used. Off Job Name (Use the job name set in the printer driver.) Job No.+Job Name Job Name+Job No. 5 When the desired job name is displayed, press [OK]. 6 Press [MENU]. The display returns to Ready. 2-46 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 71
settings) This printer supports TCP/IP and TCP/IP (IPv6) protocols. IP is an abbreviation for Internet Protocol. This printer routinely uses the checked from your PC. For more information, refer to the Command Center RX User Guide. 1 Press [MENU]. 2 Press or repeatedly until Network > appears - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 72
a network connection when a host attempts to connect to the network (Internet). This information includes the IP address of the local node and the default router (the router in the host's own network system) and the DNS (Domain Name System) server. DHCP is an extension of the BOOTP (Bootstrap - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 73
.2.0/24". In this way, "133.210.2.0/24" denotes the IP address "133.210.2.0" with a 24-bit prefix (network section). This new network address section (originally part of the host address) made possible by the subnet mask is referred to as the subnet address. Note When you enter the subnet mask, be - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 74
IP). By installing a gateway, the communications protocols and data display modes on different networks can be made compatible. On TCP/IP networks, and that Bonjour packets are accepted. If you install Bonjour on Windows XP Service Pack 2 or later, the Windows firewall will be set up correctly for - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 75
Internet protocol, TCP/IP (IPv4). IPv6 is the next-generation Internet protocol and expands the available address space, which resolves the problem of the lack of addresses under IPv4, while also introducing other improvements such as additional security functionality and the capacity to prioritize - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 76
>>DHCPv6 ? Off >>NetBEUI ? On 2-52 DHCPv6 (DHCPv6 setting) DHCPv6 is the next-generation of the Internet's Dynamic Host Configuration Protocol and supports IPv6. It extends the BOOTP startup protocol that defines the protocols used for transferring configuration information to hosts on the network. - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 77
>>SNMPv3 ? Off >>FTP(Server) ? On >>SNMP ? On >>SMTP ? Off Using the Operation Panel SNMPv3 (SNMPv3 setting) Set SNMPv3. 1 Press while >Protocol Detail > is displayed. 2 Press or repeatedly until >>SNMPv3 appears. 3 Press [OK]. A blinking question mark (?) appears. 4 Select On or Off using - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 78
>>POP3 ? Off >>RAW Port ? On >>LPD ? On 2-54 5 Press [OK]. 6 Press [MENU]. The display returns to Ready. POP3 (POP3 setting) Select whether or not to receive email using POP3. 1 Press while >Protocol Detail > is displayed. 2 Press or repeatedly until >>POP3 appears. 3 Press [OK]. A blinking - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 79
>>HTTP ? On >Restart Network ? 3 Press [OK]. A blinking question mark (?) appears. 4 Select On or Off using or . 5 Press [OK]. 6 Press [MENU]. The display returns to Ready. Restart Network (Restarting the network card) After all network related settings have been done, restart the network card - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 80
for information on the wireless network settings. Manual setting from the printer is not supported on this device. The options available in the Optional Network settings are as follows: • ID (Administrator ID input) • Password (Administrator Password input) • TCP/IP (IPv4 settings) • TCP/IP (IPv6 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 81
Administrator ID input)), the message display shows Password (Administrator password input) and a blinking cursor (_). Sequenced Packet eXchange), but the system also supports TCP/IP. The feature of the management tools from the clients. Also, all drivers and protocol stacks are in the form of - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 82
used to identify devices (computers, printers, etc.) on the network. When the power is turned on, a broadcast signal is sent out onto the network and the addresses and machine names are automatically assigned. The default setting is On. 1 After entering the administrator ID and password, press or - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 83
the administrator ID and password, press or repeatedly until >Communication appears. 2 Press [OK]. A blinking question mark (?) appears. 3 Press or to select the desired NIC. Standard NIC (standard network interface of the printer) Option NIC (optional network interface kit) 4 Press [OK - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 84
Network (Restarting the optional network interface kit) After all network related settings have been done, restart the network card of the device. This is mandatory to make the settings effective. 1 After entering the administrator ID and password, press or repeatedly until >Restart Network - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 85
printer. setting) • RAM Disk Mode (Using the RAM disk alert level for toner addition) IMPORTANT download messages in other languages. Contact your service technician for information. 1 Press while Device Common > is displayed. 2 Press or repeatedly until >Message Language appears. The default - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 86
2-94. 1 Once you have entered the correct ID in the previous step (ID (Administrator ID input)), the message display shows Password (Administrator password input) and a blinking cursor (_). 2 Press or to increase or decrease, respectively, the value at the blinking cursor. Enter the specified - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 87
/ 01 / 01 >>Time (Hour:Min:Sec) 11 : 19 : 21 >>Date Format ? Month/Day/Year Date (date setting) 1 After entering the administrator ID and password, press or repeatedly until >>Date (Year/Mon/Day) appears. 2 Press [OK]. A blinking cursor (_) appears. 3 Use the arrow keys to set the year, month - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 88
summer time. 1 After entering the administrator ID and password, press or repeatedly until >>Summer Time printer operations and the printer status. This setting is useful, for example, when the printer a tone sounds each time a key is used. The default setting is On. 1 Press while >Buzzer > is - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 89
to Ready. Error (Error tone setting) When On is selected in this setting, a tone sounds when a problem such as running out of paper or a paper jam occurs during printing. The default setting is On. 1 Press while >Buzzer > is displayed. 2 Press or repeatedly until >>Error appears. 3 Press [OK - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 90
when the printer is powered up. To printer supports two types of storage device; optional SSD and RAM disk. The optional SSD is installed into the dedicated slot of the printer. The RAM disk is an allocated part of the printer when RAM Disk Mode is set to On. 1 Press while >RAM Disk Mode On > is - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 91
time, it must be formatted before use. This menu is displayed only when the optional SSD is installed on the printer. Note If the optional SSD is installed in the printer, the Custom Box and Job Box will be available. 1 Press while Device Common > is displayed. 2 Press or repeatedly until >SSD - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 92
(Duplex printing error detection setting) If the error detection setting for duplex printing has been turned On, and you attempt to print onto a paper size and paper type that cannot be used for duplex printing, the Duplex disabled Press GO error message will be displayed and printing will stop. On - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 93
displayed when the MP tray is configured as the default paper source, and there is no paper in the MP tray, or turn it to Off Password (Administrator Password input) • Auto Panel Reset (Auto panel reset settings) • Panel Reset Timer (Setting the panel reset timer) • Low Power Timer (Low Power Mode - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 94
appears and the input screen then reappears. Re-enter the ID or password correctly. 3 Press [OK]. The Timer settings screen appears. Auto Panel Reset (Auto panel reset settings) The Auto Panel Reset function automatically restores the default settings if the panel is not used for a set time. The - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 95
Low Power Mode in the absence of a print job. The printer reverts to normal operation mode when the printer receives a print job or [GO] is pressed on the operation panel. The default time is 1 minute. 1 After entering the administrator ID and password, press or repeatedly until >>Low Power - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 96
printer and one person causes one of the above errors, after the set period of time elapses, the data sent from the next person is printed. The default (Setting the error clear time). 1 After entering the administrator ID and password, press or repeatedly until >>Auto Error Clear appears. 2 Press - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 97
setting) If the printer receives no data for a certain period, it will time out and release the current interface. It prints whatever data it has in its buffer and feeds out the page. The default form feed timeout time is 30 seconds. 1 After entering the administrator ID and password, press or - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 98
The options available in Sleep Level Set. are as follows: • ID (Administrator ID input) • Password (Administrator Password input) • Sleep Level (Sleep level setting) • Network (Setting for entering energy-saving mode when connected to a network) Note Network is only displayed when Sleep Level is set - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 99
next step Password (Administrator Password input). Password (Administrator Password input) mode and Energy Saver mode, refer to Printing Operation section in the Operation Guide. Sleep Level Set. menu is not displayed when the optional network interface kit (IB-50) or wireless network interface kit - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 100
when connected to a network) This sets whether or not the machine enters Energy Saver mode when connected to a network. 1 After entering the administrator ID and password, press or repeatedly until >>Network appears. 2 Press [OK]. A blinking question mark (?) appears. 3 Select On or Off using - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 101
. The options available in TonerAlert Level are as follows: • ID (Administrator ID input) • Password (Administrator Password input) • Off/On • TonerAlert Level (Setting for the alert level for toner addition) 1 Press while Device Common > is displayed. 2 Press or repeatedly until >TonerAlert - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 102
returns to Ready. TonerAlert Level (Setting for the alert level for toner addition) This sets the level at which toner addition alerts will be displayed. 1 After entering the administrator ID and password, press or repeatedly until >>TonerAlert Level appears. 2 Press [OK]. A blinking cursor - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 103
protect printer operation and the print data. The options available in Security are as follows: • ID (Administrator ID input) • Password (Administrator Password from your PC. For more information, refer to the Command Center RX User Guide. 1 Press [MENU]. 2 Press or repeatedly until Security > - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 104
the blinking cursor. Enter the specified password. Use and to move the cursor right and left. Enter a password consisting of between 0 (no settings slot setting) This locks and protects the USB memory slot (USB host). The default setting is Unblock. 1 Press while >I/F Block > is displayed. 2 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 105
(NIC). The default setting is Unblock. Note Option I/F is displayed only when the optional network interface is installed on the printer. 1 Press web services. Network driver use this Enhanced WSD Web service. The default setting is On. 1 After entering the administrator ID and password, press - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 106
websites and enables printing to be carried out via routers on printers in remote locations. It also supports the HTTP authentication mechanisms along with SSL server and client authentication as well as encryption. The default setting is On. Note Check with your network administrator when selecting - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 107
administrator when selecting network settings. 1 After entering the administrator ID and password, press or > repeatedly until >SSL Server > appears. from being divulged, key transfer and storage must be very strictly managed. The default setting is Off. 1 Press while >SSL Server On > is - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 108
that uses SSL for communications between users and servers in network printing. To use IPP over SSL, both server and client must support the protocol. The default setting is Off. 1 Press while >SSL Server On > is displayed. >>IPP over SSL appears. 2 Press [OK]. A blinking question mark (?) appears - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 109
32-bit IP addresses and IPv6 uses 128-bit IP addresses. The default setting is Off. Note Check with your network administrator when selecting network settings. 1 After entering the administrator ID and password, press or repeatedly until >IPSec appears. 2 Press [OK]. A blinking question mark - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 110
for the LAN interface to be used. The default setting is Auto. 1 After entering the administrator ID and password, press or repeatedly until >LAN Level setting) Security Level is primarily a menu used by service personnel for maintenance work. There is no need for customers to use this - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 111
accounting on this machine offers the following features: • Support for up to 100 departments • Department codes up 999,999) on the number of pages used • Resetting of the number of pages used for individual departments The ID input) • Password (Administrator Password input) • Job Accounting - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 112
(Job Accounting selection/setting) This allows you to turn the Job Accounting function On and Off. The default setting is Off. 1 After entering the administrator ID and password, press or repeatedly until >Job Accounting appears. 2 Press [OK]. A blinking question mark (?) appears. 3 Select On or - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 113
Output (Maximum print output setting [color + Black & White total]) • Color Max. Output (Maximum print output setting [color]) • Reset Counter (Counter reset) 1 Press while Job Accounting > is displayed. 2 Press or repeatedly until >Select Account> appears. 3 Press [OK]. A blinking question - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 114
>>Restriction ? Off >>Color Restriction ? Off >>Maximum Output 0000001 Restriction (Print restriction selection [color + Black & White total]) Sets restricted functionality for all printing on the currently selected account. You can use the restrictions to prohibit printing by individual - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 115
and 9999999 as the number of pages. Use and to move the cursor right and left. 4 Press [OK]. 5 Press [MENU]. The display returns to Ready. Reset Counter (Counter reset) Resets the counter (pages used) for the currently selected account. 1 Set the account ID and then press or repeatedly until - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 116
2-92 >Delete Account ?001 >Print Job Accounting List? 4 Press or to increase or decrease, respectively, the value at the blinking cursor. Set the desired account ID. You can set a number between 1 and 8 digits. Use and to move the cursor right and left. Note If you enter an existing - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 117
>Apply Limit ? Subsequently >Unknown ID Job ? Reject 3 Press [OK]. A blinking question mark (?) appears. 4 Press or to select a setting. Immediately (prohibit printing from this job onwards) Subsequently (prohibit printing from the next job onwards) 5 Press [OK]. 6 Press [MENU]. The display - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 118
the printer and manage other users. When using the Security and Job Accounting functions, the administrator ID and password set next step Password (Administrator Password input). Password (Administrator Password input) You can use this to set the administrator password. Note The default setting is - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 119
Ready. Change ID (Administrator ID change) You can use this to change the administrator ID. 1 In step 3 in Password (Administrator Password input) above, press or while the Admin (Change) screen is displayed until >Change ID appears. (E.g.: Where the administrator ID is 001) 2 When you press [OK - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 120
3 Press or to increase or decrease, respectively, the value at the blinking cursor. Enter the password to be changed. Use and to move the cursor right and left. Enter a password consisting of between 0 and 16 numbers. 4 Press [OK]. A confirmation screen appears. (E.g.: Where the OK? - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 121
Printer • Service (for maintenance) IMPORTANT Service is primarily a menu used by service personnel for maintenance out automatically each time the power to the printer is turned on. The color magenta, cyan or yellow) is skewed, use this mode to correct the color registration on the operation panel. - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 122
this option to print a color registration correction chart for use in correcting the color registration. 1 Press while Adjust/Maintenance > is displayed. 2 Press or repeatedly until >Registration Normal > appears. 3 Press . 4 Press or repeatedly until >>Print Registration Chart appears - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 123
printing ends, the display returns to Ready. Adjust Magenta Corrects the registration for magenta (red). 1 Press while Adjust/Maintenance > is displayed. 2 Press or repeatedly until >Registration Normal > appears. 3 Press . 4 Press or repeatedly until >>Adjust Magenta appears. 5 Press - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 124
line is not 0, redo the settings again from step 4 above. IMPORTANT If the problem of skewed-color printout still persists even after correcting the color registration, call for service. Registration Details (Color registration [detailed]) This allows you to make fine horizontal and vertical - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 125
this option to print a color registration correction chart for use in correcting the color registration. 1 Press while Adjust/Maintenance > is displayed. 2 Press or repeatedly until >Registration Details > appears. 3 Press . 4 Press or repeatedly until >>Print Registration Chart appears - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 126
7 When printing ends, the display returns to Ready. M 12345 3 (Adjust magenta) Makes detailed corrections to the registration for magenta (red). 1 Press while Adjust/Maintenance > is displayed. 2 Press or repeatedly until >Registration Details > appears. 3 Press . Using the Operation Panel - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 127
. If the section where the lines most closely coincide as a single straight line is not 0, redo the settings again from step 4 above. IMPORTANT If the problem of skewed-color printout still persists even after correcting the color registration, call for - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 128
page) • Print Test Page • Maintenance (New Maintenance Kit replacement confirmation setting) • DEV-CLN (Developer/Refresh mode setting) • LSU (LSU cleaning mode setting) • Drum (Drum/Refresh mode setting) IMPORTANT Service is primarily a menu used by service personnel for maintenance work. There is - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 129
status page is printed out. 5 When printing ends, the display returns to Ready. Print Test Page The test page is printed to check the effectiveness of printer adjustments. This is primarily used for maintenance by service personnel, but it contains information that may also be useful to you. 1 Press - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 130
Maintenance Kit (resets the total number of Maintenance Kit print images). This is primarily used for maintenance by service personnel. Note The Maintenance the display returns to Ready. LSU (LSU cleaning mode setting) This sets the cleaning mode for the LSU. When the printing quality declines, - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 131
>>Drum ? Drum (Drum/Refresh mode setting) This sets the refresh mode for the drum. When the printing quality declines, refreshing the drum can restore the printing quality. This is primarily used for maintenance by service personnel. 1 Press while >Service > is displayed. 2 Press or - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 132
2-108 Using the Operation Panel - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 133
3 Options This chapter contains explanations on the following topics: General Information 3-2 Expansion Memory Modules 3-3 General Description of Options 3-5 For availability of the options, consult your service technician. Options 3-1 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 134
General Information This printer has the following options available to satisfy your printing requirements. For instructions on installing individual options, refer to the documentation included with the option. Some options are explained in the following sections. Paper Feeder PF-500/ PF-510 USB - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 135
the printer's memory up to 1536 MB by plugging in the optional memory modules. Note A 512 MB memory module is already installed at the factory. To MB. Precautions for Handling the Printer's Main Controller Board and Memory Modules To protect electronic parts, discharge static electricity from your - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 136
Installing the Memory Modules IMPORTANT Remove any USB memory that is attached to the printer's USB memory slot. 1 Power off the printer and unplug the printer power cord. 2 Unscrew two screws at the back of the main controller board. Main Controller Board 3 Pull out the main controller board - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 137
the printer's own cassette. IMPORTANT When you use the paper feeder, place the papers and envelopes print-side up. The papers that can be used in the cassettes supplied with the paper feeders are as follows: PF-500 : Paper size : Envelope Monarch, Envelope #10, Envelope #9, Envelope #6, Envelope DL - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 138
Slot 3-6 SSD With SSD installed in the printer, received data can be rasterized and stored -50 User's Manual. Wireless Network Interface Kit (IB-51) This is a wireless network interface kit which supports the wireless network on supported USB memory devices, contact your service technician. Options - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 139
4 Computer Interface This chapter contains explanations on the following topics: Interface 4-2 USB Interface 4-2 Network Interface 4-3 Computer Interface 4-1 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 140
Connectors Printer: B-type receptacle (female) with upstream port Cable: B-type plug (male) Cable Use a shielded cable that complies with USB 2.0 (Hi-Speed USB) and not longer than 5 meters (16 feet). Transfer Mode High speed (480 Mbps maximum) Full-Speed (12 Mbps maximum) Power Control Self-power - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 141
be password-protected. Support for a Range of Protocols The SMTP, POP3, SSL, SNMP, IPv6 and NetBIOS over TCP/IP protocols are supported for easier printer management and more robust security. Support for IEEE 802.1X The interface supports EAP-TLS and PEAP authentication. Supports IPv6 Supports IPv6 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 142
Operation Environment 10 to 35 °C (50 to 95 °F), 20-80 % RH (condensation-free) EMI Countermeasures VCCI Class B, FCC Class B (U.S.), CE (Europe) IMPORTANT When IPv6 functions are used, the devices used on the network (routers, PCs, etc) must support IPv6. 4-4 Computer Interface - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 143
used in this machine, contact your service technician. AppleTalk AppleTalk offers file sharing and printer sharing and it also enables you to IP address, data is sent to the host that is designated as the Default Gateway. DHCP (Dynamic Host Configuration Protocol) This is a protocol that - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 144
copies of the stored data later using the printer's operation panel. KPDL KPDL is Kyocera's implementation of the PostScript page description language Level3. MP Tray This tray is used instead of the cassette when printing on envelopes, postcards, transparency sheets, and labels. NetBEUI (NetBIOS - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 145
Printer driver The printer driver makes it possible for you to print data created using application software. The printer driver for the printer is contained on the DVD-ROM supplied with the printer. Install the printer driver In this mode, power is reduced to the minimum. The default setting can be - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 146
such as the machine's memory, the total number of prints and paper source settings. You can print the status page from the operation Internet protocol and expands the available address space, which resolves the problem of the lack of addresses under IPv4, while also introducing other improvements - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 147
95 Administrator Password 2-56, Paper type 2-33 Color Calibration 2-97 Color Mode Color or Black & White 2-42 Color Registration Detailed 2-100 Standard 2-97 Conventions vi Counter 2-28 Custom Box 2-18 Custom box list 2-21 Manipulating data 2-19 Select box 2-18 D Date Setting 2-62 Default - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 148
Wide A4 pitch 2-44 XPS FitTo page 2-45 Paper Availability 1-2 Colored 1-11 Envelope 1-10 Guidelines 1-4 Label 1-9 Minimum and maximum 2-66 Restart Printer 2-104 S Size Dial 2-31 Sleep Level 2-73 Sleep mode Glossary-3 Special Paper 1-7 Specifications Network interface 4-3 Paper 1-2 USB - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 149
Low power Panel reset Sleep Toner Alert Level 2-71 2-70 2-71 2-77 U Unit of Measurement 2-32 USB Interface 4-2 USB Memory 2-16 W Wireless Network Interface Kit 3-6 WSD-PRINT 2-81 Index-3 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 150
Index-4 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 151
We recommend the use of our own brand supplies. We will not be liable for any damage caused by the use of third party supplies in this machine. A1 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 152
Hong Kong Limited 16/F.,Mita Centre, 552-566, Castle Peak Road Tsuenwan, NT, Hong Kong Phone: +852-2429-7422 Fax: +852-2423-2159 KYOCERA Document Solutions Taiwan Corporation 6F., No.37, Sec. 3, Minquan E. Rd., Zhongshan Dist., Taipei 104, Taiwan R.O.C. Phone: +886-2-2507-6709 Fax: +886-2-2507-8432 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 153
Lda. Rua do Centro Cultural, 41 (Alvalade) 1700-106 Lisboa, Portugal Phone: +351-21-843-6780 Fax: +351-21-849-3312 KYOCERA Document Solutions South Africa (Pty) Ltd. KYOCERA House, Hertford Office Park, 90 Bekker Road (Cnr. Allandale), Midrand, South Africa. Phone: +27-11-540-2600 Fax: +27-11-466 - Kyocera ECOSYS P6030cdn | ECOSYS P6030cdn Operation Guide (Advanced) - Page 154
Rev.1 2013.12 2PPKDEN401
PRINT
ADVANCED
OPERATION GUIDE
ECOSYS P6030cdn