Kyocera ECOSYS P6030cdn ECOSYS P6030cdn Operation Guide (Advanced) - Page 96

Auto Error Clear Auto error clear setting, Error Clear Timer Setting the error clear time

Get Kyocera ECOSYS P6030cdn PDF manuals and user guides View all Kyocera ECOSYS P6030cdn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

>>Auto Error Clear ? Off >>Error Clear Timer 030sec. Auto Error Clear (Auto error clear setting) If an error that still allows you to continue printing occurs, the next received data is automatically printed after a set period of time elapses. For example, if the printer is shared over a network as a network printer and one person causes one of the above errors, after the set period of time elapses, the data sent from the next person is printed. The default setting is Off (Auto Error Clear disabled). The auto clear errors are: • Memory overflow Press GO • KPDL error ## Press GO • SSD error ## Press GO • RAM disk error## Press GO • Illegal Account Press GO • Exceeded Max.out Press GO • Job restricted Press GO • Account error ## Press GO • Duplex disabled Press GO • Job not stored Press GO • No multi copies Press GO • USB memory error ## Press GO For setting the auto error clear recovery time, refer to the next section Error Clear Timer (Setting the error clear time). 1 After entering the administrator ID and password, press  or  repeatedly until >>Auto Error Clear appears. 2 Press [OK]. A blinking question mark (?) appears. 3 Select On or Off using  or . 4 Press [OK]. 5 Press [MENU]. The display returns to Ready. Error Clear Timer (Setting the error clear time) If Auto Error Clear is set to On and a non-fatal error (an error that allows printing to continue) occurs, this setting specifies the time until the error is recovered and printing resumes. 1 After entering the administrator ID and password, press  or  repeatedly until >>Error Clear Timer appears. 2 Press [OK]. A blinking cursor (_) appears. 3 Press  or  to increase or decrease the value at the blinking cursor and set the desired time. The time must be set between 005 and 495 seconds, in 5-second increments. You can use  and  to move the cursor right and left. 4 Press [OK]. 5 Press [MENU]. The display returns to Ready. 2-72 Using the Operation Panel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
2-72
Using the Operation Panel
Auto Error Clear (Auto error clear setting)
If an error that still allows you to continue printing occurs, the next
received data is automatically printed after a set period of time elapses.
For example, if the printer is shared over a network as a network printer
and one person causes one of the above errors, after the set period of
time elapses, the data sent from the next person is printed. The default
setting is
Off
(Auto Error Clear disabled).
The auto clear errors are:
• Memory overflow Press GO
• KPDL error
## Press GO
• SSD error ## Press GO
• RAM disk error## Press GO
• Illegal Account Press GO
• Exceeded Max.out Press GO
• Job restricted Press GO
• Account error ## Press GO
• Duplex disabled Press GO
• Job not stored Press GO
• No multi copies Press GO
• USB memory error ## Press GO
For setting the auto error clear recovery time, refer to the next section
Error Clear Timer (Setting the error clear time)
.
1
After entering the administrator ID and password, press
or
repeatedly until
>>Auto Error Clear
appears.
2
Press
[OK]
. A blinking question mark (
?
) appears.
3
Select
On
or
Off
using
or
.
4
Press
[OK]
.
5
Press
[MENU]
. The display returns to
Ready
.
Error Clear Timer (Setting the error clear time)
If Auto Error Clear is set to
On
and a non-fatal error (an error that allows
printing to continue) occurs, this setting specifies the time until the error
is recovered and printing resumes.
1
After entering the administrator ID and password, press
or
repeatedly until
>>Error Clear Timer
appears.
2
Press
[OK]
. A blinking cursor (
_
) appears.
3
Press
or
to increase or decrease the value at the blinking cursor
and set the desired time. The time must be set between
005
and
495
seconds, in 5-second increments. You can use
and
to move the
cursor right and left.
4
Press
[OK]
.
5
Press
[MENU]
. The display returns to
Ready
.
>>Auto Error Clear
? Off
>>Error Clear Timer
030
sec.