Kyocera ECOSYS P6030cdn ECOSYS P6030cdn Operation Guide (Advanced) - Page 101

TonerAlert Level Setting for the alert level for toner, addition

Get Kyocera ECOSYS P6030cdn PDF manuals and user guides View all Kyocera ECOSYS P6030cdn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

TonerAlert Level (Setting for the alert level for toner addition) This sets the toner addition alert level displayed on the status monitor. The options available in TonerAlert Level are as follows: • ID (Administrator ID input) • Password (Administrator Password input) • Off/On • TonerAlert Level (Setting for the alert level for toner addition) 1 Press  while Device Common > is displayed. 2 Press  or  repeatedly until >TonerAlert Level > appears. >TonerAlert Level > ID _ Password _ ID (Administrator ID input) To use the TonerAlert Level settings, you must enter an administrator ID. For information on how to set the administrator ID, refer to Administrator (Administrator settings) on page 2-94. 1 Press  while >TonerAlert Level > is displayed. 2 The message display shows ID and a blinking cursor (_). 3 Press  or  to increase or decrease, respectively, the value at the blinking cursor. Enter the specified ID. Use  and  to move the cursor right and left. Enter an ID consisting of between 1 and 16 numbers. 4 Press [OK]. Proceed to the next step Password (Administrator Password input). Password (Administrator Password input) To set up the TonerAlert Level settings, you must enter an administrator ID and administrator password. For information on how to set the administrator password, refer to Administrator (Administrator settings) on page 2-94. 1 Once you have entered the correct ID in the previous step (ID (Administrator ID input)), the message display shows Password (Administrator password input) and a blinking cursor (_). 2 Press  or  to increase or decrease, respectively, the value at the blinking cursor. Enter the specified password. Use  and  to move the cursor right and left. Enter a password consisting of between 0 (no settings) and 16 numbers. Note If you enter the incorrect administrator ID or password, the message Wrong ID or Wrong Password appears and the input screen then reappears. Re-enter the ID or password correctly. 3 Press [OK]. The TonerAlert Level settings screen appears. Using the Operation Panel 2-77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Using the Operation Panel
2-77
TonerAlert Level (Setting for the alert level for toner
addition)
This sets the toner addition alert level displayed on the status monitor.
The options available in TonerAlert Level are as follows:
•
ID (Administrator ID input)
•
Password (Administrator Password input)
•
Off/On
•
TonerAlert Level (Setting for the alert level for toner addition)
1
Press
while
Device Common >
is displayed.
2
Press
or
repeatedly until
>TonerAlert Level >
appears.
ID (Administrator ID input)
To use the TonerAlert Level settings, you must enter an administrator ID.
For information on how to set the administrator ID, refer to
Administrator
(Administrator settings) on page 2-94
.
1
Press
while
>TonerAlert Level >
is displayed.
2
The message display shows
ID
and a blinking cursor (
_
).
3
Press
or
to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified ID. Use
and
to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4
Press
[OK]
. Proceed to the next step
Password (Administrator
Password input)
.
Password (Administrator Password input)
To set up the TonerAlert Level settings, you must enter an administrator
ID and administrator password. For information on how to set the
administrator password, refer to
Administrator (Administrator settings) on
page 2-94
.
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows
Password
(Administrator password input) and a blinking cursor (
_
).
2
Press
or
to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use
and
to move
the cursor right and left. Enter a password consisting of between 0 (no
settings) and 16 numbers.
3
Press
[OK]
. The TonerAlert Level settings screen appears.
>TonerAlert Level
>
ID
_
Password
_
Note
If you enter the incorrect administrator ID or password,
the message
Wrong ID
or
Wrong Password
appears and
the input screen then reappears. Re-enter the ID or password
correctly.