Kyocera ECOSYS P6030cdn ECOSYS P6030cdn Operation Guide (Advanced) - Page 98

Except for Europe

Get Kyocera ECOSYS P6030cdn PDF manuals and user guides View all Kyocera ECOSYS P6030cdn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Password _ Password (Administrator Password input) To set up the Sleep Level settings, you must enter an administrator ID and administrator password. For information on how to set the administrator password, refer to Administrator (Administrator settings) on page 2-94. 1 Once you have entered the correct ID in the previous step (ID (Administrator ID input)), the message display shows Password (Administrator password input) and a blinking cursor (_). 2 Press  or  to increase or decrease, respectively, the value at the blinking cursor. Enter the specified password. Use  and  to move the cursor right and left. Enter a password consisting of between 0 (no settings) and 16 numbers. Note If you enter the incorrect administrator ID or password, the message Wrong ID or Wrong Password appears and the input screen then reappears. Re-enter the ID or password correctly. 3 Press [OK]. The Sleep Level settings screen appears. >>Network ? On Network (Setting for entering sleep mode when connected to a network) This sets whether or not the machine enters sleep mode when connected to a network. 1 After entering the administrator ID and password, press  or  repeatedly until >>Network appears. 2 Press [OK]. A blinking question mark (?) appears. 3 Select On or Off using  or . 4 Press [OK]. 5 Press [MENU]. The display returns to Ready. Except for Europe Select the sleep level. The options available in Sleep Level Set. are as follows: • ID (Administrator ID input) • Password (Administrator Password input) • Sleep Level (Sleep level setting) • Network (Setting for entering energy-saving mode when connected to a network) Note Network is only displayed when Sleep Level is set to Energy Saver. 1 Press  while Device Common > is displayed. 2 Press  or  repeatedly until >Sleep Level Set. > appears. >Sleep Level Set. > 2-74 Using the Operation Panel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
2-74
Using the Operation Panel
Password (Administrator Password input)
To set up the Sleep Level settings, you must enter an administrator ID and
administrator password. For information on how to set the administrator
password, refer to
Administrator (Administrator settings) on page 2-94
.
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows
Password
(Administrator password input) and a blinking cursor (
_
).
2
Press
or
to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use
and
to move
the cursor right and left. Enter a password consisting of between 0 (no
settings) and 16 numbers.
3
Press
[OK]
. The Sleep Level settings screen appears.
Network (Setting for entering sleep mode when connected to a
network)
This sets whether or not the machine enters sleep mode when connected
to a network.
1
After entering the administrator ID and password, press
or
repeatedly until
>>Network
appears.
2
Press
[OK]
. A blinking question mark (
?
) appears.
3
Select
On
or
Off
using
or
.
4
Press
[OK]
.
5
Press
[MENU]
. The display returns to
Ready
.
Except for Europe
Select the sleep level.
The options available in Sleep Level Set. are as follows:
•
ID (Administrator ID input)
•
Password (Administrator Password input)
•
Sleep Level (Sleep level setting)
•
Network (Setting for entering energy-saving mode when connected to
a network)
1
Press
while
Device Common >
is displayed.
2
Press
or
repeatedly until
>Sleep Level Set. >
appears.
Password
_
Note
If you enter the incorrect administrator ID or password,
the message
Wrong ID
or
Wrong Password
appears and
the input screen then reappears. Re-enter the ID or password
correctly.
>>Network
? On
Note
Network
is only displayed when
Sleep Level
is set to
Energy Saver
.
>Sleep Level Set.
>