Lenovo 0768AFU User Manual - Page 18

Important, Attention - outlet

Get Lenovo 0768AFU PDF manuals and user guides View all Lenovo 0768AFU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Safety information Important Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock. v Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly. v Do not work alone under hazardous conditions or near equipment that has hazardous voltages. v Disconnect all power before: - Performing a mechanical inspection - Working near power supplies - Removing or installing main units v Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position. v If you need to work on a machine that has exposed electrical circuits, observe the following precautions: - Ensure that another person, familiar with the power-off controls, is near you. Attention: Another person must be there to switch off the power, if necessary. - Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back. Attention: An electrical shock can occur only when there is a complete circuit. By observing the above rule, you may prevent a current from passing through your body. - When using testers, set the controls correctly and use the approved probe leads and accessories for that tester. - Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames. Observe the special safety precautions when you work with very high voltages; Instructions for these precautions are in the safety sections of maintenance information. Use extreme care when measuring high voltages. v Regularly inspect and maintain your electrical hand tools for safe operational condition. v Do not use worn or broken tools and testers. v Never assume that power has been disconnected from a circuit. First, check that it has been powered off. v Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. 12 MT 0689, 0768, and 0769

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
Important
Use
only
approved
tools
and
test
equipment.
Some
hand
tools
have
handles
covered
with
a
soft
material
that
does
not
insulate
you
when
working
with
live
electrical
currents.
Many
customers
have,
near
their
equipment,
rubber
floor
mats
that
contain
small
conductive
fibers
to
decrease
electrostatic
discharges.
Do
not
use
this
type
of
mat
to
protect
yourself
from
electrical
shock.
v
Find
the
room
emergency
power-off
(EPO)
switch,
disconnecting
switch,
or
electrical
outlet.
If
an
electrical
accident
occurs,
you
can
then
operate
the
switch
or
unplug
the
power
cord
quickly.
v
Do
not
work
alone
under
hazardous
conditions
or
near
equipment
that
has
hazardous
voltages.
v
Disconnect
all
power
before:
–
Performing
a
mechanical
inspection
–
Working
near
power
supplies
–
Removing
or
installing
main
units
v
Before
you
start
to
work
on
the
machine,
unplug
the
power
cord.
If
you
cannot
unplug
it,
ask
the
customer
to
power-off
the
wall
box
that
supplies
power
to
the
machine,
and
to
lock
the
wall
box
in
the
off
position.
v
If
you
need
to
work
on
a
machine
that
has
exposed
electrical
circuits,
observe
the
following
precautions:
–
Ensure
that
another
person,
familiar
with
the
power-off
controls,
is
near
you.
Attention:
Another
person
must
be
there
to
switch
off
the
power,
if
necessary.
–
Use
only
one
hand
when
working
with
powered-on
electrical
equipment;
keep
the
other
hand
in
your
pocket
or
behind
your
back.
Attention:
An
electrical
shock
can
occur
only
when
there
is
a
complete
circuit.
By
observing
the
above
rule,
you
may
prevent
a
current
from
passing
through
your
body.
–
When
using
testers,
set
the
controls
correctly
and
use
the
approved
probe
leads
and
accessories
for
that
tester.
–
Stand
on
suitable
rubber
mats
(obtained
locally,
if
necessary)
to
insulate
you
from
grounds
such
as
metal
floor
strips
and
machine
frames.
Observe
the
special
safety
precautions
when
you
work
with
very
high
voltages;
Instructions
for
these
precautions
are
in
the
safety
sections
of
maintenance
information.
Use
extreme
care
when
measuring
high
voltages.
v
Regularly
inspect
and
maintain
your
electrical
hand
tools
for
safe
operational
condition.
v
Do
not
use
worn
or
broken
tools
and
testers.
v
Never
assume
that
power
has
been
disconnected
from
a
circuit.
First,
check
that
it
has
been
powered
off.
v
Always
look
carefully
for
possible
hazards
in
your
work
area.
Examples
of
these
hazards
are
moist
floors,
nongrounded
power
extension
cables,
power
surges,
and
missing
safety
grounds.
v
Do
not
touch
live
electrical
circuits
with
the
reflective
surface
of
a
plastic
dental
mirror.
The
surface
is
conductive;
such
touching
can
cause
personal
injury
and
machine
damage.
Safety
information
12
MT
0689,
0768,
and
0769