Marantz SR5005 SR5005 User Manual - English - Page 40

Set up speakers

Get Marantz SR5005 PDF manuals and user guides View all Marantz SR5005 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Simple version Basic version SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS Set up speakers around items indicate the settings. This section provides the setup methods of speaker systems other than the 7.1-channel system (with surround back speakers). For the setup methods of the 7.1-channel system with surround back speakers, see "Set up speakers (Audyssey® Auto Setup)" (vpage 6) of "Simple version". First install and connect the speakers to this unit. 1 Set up the remote control unit nn Set up the operation mode Press AMP to set the remote control unit to amplifier operation mode. Press AMP 2 Connect the setup microphone. When the setup microphone is connected, the following screen is displayed. 3-1.Audyssey Auto Setup MultEQ Please place microphone at ear height at main listening position. F.Height : Measure Front Sp. : A Amp Assign: Normal Start Cancel [ENT]:Select [RTN]:Back 3 Set up "Amp Assign" Use ui to select "Amp Assign". 3-1.Audyssey Auto Setup MultEQ Please place microphone at ear height at main listening position. F.Height : Measure Front Sp. : A Amp Assign: Normal Start Cancel [RTN]:Back 4 Use o p to select the configuration of the connected speakers. Normal ZONE2 SPKR-C Set when using 7.1-channel (Front/Center/Surround/Surround Back or Front height/Subwoofer) speakers. Set for connecting the speakers for ZONE2 to the SURR. BACK/ AMP ASSIGN terminals. Set for connecting a tweeter of a front speaker to the SURR. BACK/AMP ASSIGN terminals and a woofer of the front speaker to the FRONT A terminals. 5 Set up "F. Height" Press u to select "F. Height". Measure Set to measure the front height speakers. Skip Set not to measure the front height speakers. 6 Set up "Front.Sp." Use ui to select "Front Sp." and then press o p to select a speaker. A Select this to use front speaker A. B Select this to use front speaker B. A+B Select this to use front speakers A and B simultaneously. NOTE If "Mesure" is selected in step 5, select "A". If "B" is selected, the "F.Height" measurement cannot be performed. 7 Proceed to page 8 " Preparation " step 5. NOTE After performing Audyssey Auto Setup, do not change the speaker connections or subwoofer volume. In event of a change, perform Audyssey Auto Setup again. DEUTSCH ENGLISH Advanced version Information Remote control operation buttons Move the cursor (Up/Down/Left/Right) Confirm the setting Return to previous menu 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
37
Basic version
Simple version
Information
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
Advanced version
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
1
Set up
the remote control unit
n
Set up the operation mode
Press
AMP
to set the remote control
unit to amplifier operation mode.
Press AMP
2
Connect the setup microphone.
3-1.Audyssey Auto Setup
MultEQ
at ear height at
Amp Assign: Normal
Front Sp. :
A
F.Height
: Measure
Start
Cancel
[ENT]:Select [RTN]:Back
Please place microphone
main listening position.
When the setup microphone is
connected, the following screen is
displayed.
3
Set up “Amp Assign”
Use
ui
to select “Amp Assign”.
3-1.Audyssey Auto Setup
MultEQ
at ear height at
Start
Cancel
[RTN]:Back
Please place microphone
main listening position.
Front Sp. :
A
F.Height
: Measure
Amp Assign: Normal
4
Use
o
p
to select the configuration
of the connected speakers.
Normal
Set when using 7.1-channel
(Front/Center/Surround/Surround
Back or Front height/Subwoofer)
speakers.
ZONE2
Set for connecting the speakers
for ZONE2 to the SURR. BACK/
AMP ASSIGN terminals.
SPKR-C
Set for connecting a tweeter of
a front speaker to the SURR.
BACK/AMP ASSIGN terminals
and a woofer of the front speaker
to the FRONT A terminals.
5
Set up “F. Height”
Press
u
to select “F. Height”.
Measure
Set to measure the front height
speakers.
Skip
Set not to measure the front
height speakers.
Set up speakers
around items indicate the settings.
This section provides the setup methods of speaker systems other than the 7.1-channel system (with surround back speakers).
For the setup methods of the 7.1-channel system with surround back speakers, see “Set up speakers (Audyssey® Auto Setup)” (
v
page 6) of “Simple
version”.
First install and connect the speakers to this unit.
6
Set up “Front.Sp.”
Use
ui
to select “Front Sp.” and
then press
o
p
to select a speaker.
A
Select this to use front speaker A.
B
Select this to use front speaker B.
A+B
Select this to use front speakers A and B
simultaneously.
NOTE
If “Mesure” is selected in step 5, select “A”. If
“B” is selected, the “F.Height” measurement
cannot be performed.
7
Proceed to page 8
“
Preparation
” step 5.
NOTE
After performing Audyssey Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu