Marantz SR5005 SR5005 User Manual - English - Page 65

Other settings

Get Marantz SR5005 PDF manuals and user guides View all Marantz SR5005 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Other settings Remote control settings • When you connect a remote control receiver unit (purchased separately) to the REMOTE CONTROL IN terminal of this unit, use the following procedure to disable the remote sensor function of this unit. • The remote sensor function of remote control signals is enabled by default. ENTER o p RETURN ZONE2 ON/OFF Switching the on-screen display output mode Set whether the menu is operated by the monitor connected to the VIDEO OUT terminal or the monitor connected to the COMPONENT VIDEO MONITOR OUT terminal. • The factory setting is "Comp". RETURN PURE DIRECT nnDisabling the sensor function of the remote control 1 To enable the remote signal sensor function, press and hold ZONE2 ON/OFF and RETURN for 3 seconds. "IR:< ENABLE >" is displayed. 2 Press o p to select "DISABLE". 3 Press ENTER. The sensor function of the remote control signal of this unit is disabled. NOTE If a remote control receiver unit (purchased separately) is not connected, do not perform this setting. If you do, you will not be able to operate this unit using the remote control. nnEnabling the remote sensor function 1 To disable the remote signal sensor function, press and hold ZONE2 ON/OFF and RETURN for 3 seconds. "IR:< DISABLE >" is displayed. 2 Press o p to select "ENABLE". ENTER o p 1 Press and hold RETURN and PURE DIRECT for 3 seconds. Corresponding to the video signal format settings, "OSD Out: 0 Comp 1" or "OSD Out: 0 Video 1" is shown in the display. 2 Press o p to change the settings according to the connection method. Comp Video Set when the COMPONENT VIDEO MONITOR OUT connector is connected to a TV. Set when the VIDEO OUT connector is connected to a TV. 3 Press ENTER to enter the setting. NOTE When operating the on-screen display menu using the monitor connected to the HDMI OUT terminal, either setting may be used without problem. 3 Press ENTER. The sensor function of the remote control signal of this unit is enabled. 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
62
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
Other settings
Remote control settings
• When you connect a remote control receiver unit (purchased
separately) to the REMOTE CONTROL IN terminal of this unit, use
the following procedure to disable the remote sensor function of
this unit.
• The remote sensor function of remote control signals is enabled by
default.
o
p
ZONE2 ON/OFF
RETURN
ENTER
n
Disabling the sensor function of the remote control
1
To enable the remote signal sensor function, press
and hold
ZONE2 ON/OFF
and
RETURN
for 3 seconds.
“IR:<
ENABLE
>” is displayed.
2
Press
o
p
to select “DISABLE”.
3
Press
ENTER
.
The sensor function of the remote control signal of this unit is
disabled.
NOTE
If a remote control receiver unit (purchased separately) is not
connected, do not perform this setting. If you do, you will not be
able to operate this unit using the remote control.
n
Enabling the remote sensor function
1
To disable the remote signal sensor function, press
and hold
ZONE2 ON/OFF
and
RETURN
for 3 seconds.
“IR:<
DISABLE
>” is displayed.
2
Press
o
p
to select “ENABLE”.
3
Press
ENTER
.
The sensor function of the remote control signal of this unit is
enabled.
Switching the on-screen display
output mode
Set whether the menu is operated by the monitor connected to the
VIDEO OUT terminal or the monitor connected to the COMPONENT
VIDEO MONITOR OUT terminal.
• The factory setting is “Comp”.
ENTER
o
p
RETURN
PURE DIRECT
1
Press and hold
RETURN
and
PURE DIRECT
for 3
seconds.
Corresponding to the video signal format settings,
“OSD Out:
0
Comp
1
” or “OSD Out:
0
Video
1
” is shown
in the display.
2
Press
o
p
to change the settings according to the
connection method.
Comp
Set when the COMPONENT VIDEO MONITOR OUT
connector is connected to a TV.
Video
Set when the VIDEO OUT connector is connected
to a TV.
3
Press
ENTER
to enter the setting.
NOTE
When operating the on-screen display menu using the monitor
connected to the HDMI OUT terminal, either setting may be used
without problem.