Marantz SR5005 SR5005 User Manual - English - Page 61

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL Setting items Setting details Channel Level Test Tone Start : Output test tone. Set the volume of the test • FL / C / FR / SR / SBRz / SBLz / SL / FHL / FHR / SW : Select the tone to be the same when it speaker. is output from each speaker. zz When the "Speaker Config." - "S.Back" setting (vpage 57) is set to "1sp", "S.Back" is displayed. • -12.0dB - +12.0dB (0.0dB) : Adjust the volume. • When o is pressed while the subwoofer volume is set to "-12 dB", the "Subwoofer" setting switches to "OFF". • When "Channel Level" is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 40. • When you press TEST TONE on the remote control, you can enter this setting item immediately. NOTE • Speakers set to "None" in the "Speaker Config." (vpage 56) settings are not displayed. • When a headphones jack is inserted in the PHONES jack of this unit, the "Channel Level" is not displayed. Default : The "Channel Level" settings are returned to the default settings. • Yes : Reset to the defaults. • No : Do not reset to the defaults. Crossover Freq. Crossover : Set the crossover frequency. Set the maximum frequency • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / of the bass signal output 250Hz from each channel to the subwoofer. Set the Crossover Freq. to suit the bass reproduction capability of the speaker being used. Advanced : Specify crossover frequency for each speaker. • Front / Center / Surround / S.Back / Front Height : Select the speaker. • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz : Set the crossover frequency. • "Crossover Freq." can be set when the "Bass Setting" - "Subwoofer Mode" (vpage 57) setting is "LFE+Main", or when you have a speaker that is set to "Small". • Always set the crossover frequency to "80Hz". When using small speakers, however, we recommend setting the crossover frequency to a higher frequency. • For speakers set to "Small", sound below the crossover frequency is cut from the sound output. The cut bass sound is output from the subwoofer or front speakers. • The speakers that can be set when "Advanced" is selected differ depending on the "Subwoofer Mode" setting (vpage 57). • When "LFE" is selected, speakers set to "Small" at "Speaker Config." can be set. If the speakers are set to "Large", "Full Band" is displayed and the setting cannot be made. • If set to "LFE+Main", this setting can be made regardless of the speaker size. NEDERLANDS SVENSKA Setting items Front Speaker Setup Set the front speakers to use for every surround mode. Setting details • A：Front speaker A is used. • B：Front speaker B is used. • A+B：Both front speakers A and B are used. You can switch speakers by pressing SPKR A/B on the remote control. Manual Setup HDMI Setup Default settings are underlined. Make settings for HDMI video/audio output. Setting items Setting details Auto Lip Sync Make automatic compensation for timing shift in audio and video output. ON : Compensated. OFF : Not compensated. HDMI Audio Out Select HDMI audio output device. Amp : Play back through speakers connected to the receiver. TV : Play back through TV connected to the receiver. When the HDMI control function is activated, priority is given to the TV audio setting (vpage 39 "HDMI control function"). HDMI Control You can link operations with devices connected to HDMI and compatible with HDMI Control. ON : Use HDMI control function. OFF : Do not use HDMI control function. • When a device that is not compatible with the HDMI control function is connected, set "HDMI Control" to "OFF". • Please consult the operating instructions for each connected component to check the settings. • Refer to "HDMI control function" (vpage 39) for more information about the HDMI control function. NOTE • When "HDMI Control" is set to "ON", it consumes more standby power. If you are not using this unit for an extended period, it is recommended that you unplug the power cord from the power outlet. • "HDMI Control" does not work when the power to the equipment is off. Either turn power on or set to standby. • The HDMI control function controls operations of a TV that is compatible with the HDMI control function. Make sure that the TV and HDMI are connected when you perform HDMI control. • If the "HDMI Control" settings have been changed, always reset the power to connected devices after the change. 58 Remote control operation buttons Move the cursor (Up/Down/Left/Right) Confirm the setting Return to previous menu