Panasonic PVDV953D Digital Video Camera - Page 14

POWER SUPPLY, CHARGING TIME AND AVAILABLE RECORDING TIME, Using the AC Adaptor, Using the Battery

Get Panasonic PVDV953D - DIGITAL VIDEO CAMCOR PDF manuals and user guides View all Panasonic PVDV953D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

1 1 3 2 1 2 2 PUSH BAT T 1 O FF ON MODE CGR-D16 CGP-D28 CGR-D53 A 2 h. B 2 h 20 min. (2 h.) A 3 h 15 min. B 4 h 05 min. (3 h 25 min.) A 5 h 20 min. B 7 h 40 min. (6 h 25 min.) Power Supply ª Using the AC Adaptor 1 Insert the battery-shaped connector of the DC Cable into the Battery Holder on the Palmcorder. 2 Connect the DC Cable to the [DC OUT] Jack on the AC Adaptor. 3 Connect the AC Adaptor and AC Cable. ≥The AC Cable's outlet plug cannot be pushed fully into the AC Adaptor Jack. A gap will remain as shown 1. ≥Before connecting or disconnecting the power supply, set the [OFF/ ON/MODE] Switch on the Palmcorder to [OFF] and make sure that [CAMERA/VCR/CARD P.B.] Lamps are not lit. ≥Battery cannot be charged if DC Cable is connected to AC Adapter. ª Using the Battery Before use, fully charge the battery. 1 Attach the Battery to AC Adaptor and charge it. ≥Since the Battery will not be charged when the DC Cable is connected to the AC Adaptor, disconnect it. ≥The [POWER] Lamp and [CHARGE] Lamp lights up, and charging starts. ≥When the [CHARGE] Lamp goes off, charging is completed. 2 Attach the charged Battery to the Palmcorder. Disconnecting the Power Source Set the [OFF/ON/MODE] Switch 1 to [OFF], and while pressing the [PUSH BATT] Button 2, slide the Battery or battery-shaped connector upward to disconnect it. ≥When attaching or removing battery, set [OFF/ON/MODE] Switch to [OFF] and make sure the Operation Mode Lamp is not lit. ≥When the Palmcorder is used for a long time, the Camera body becomes warm, but this is not a malfunction. ≥If the [CHARGE] Lamp does not light up, although the Battery is attached to the AC Adaptor, detach the Battery and reattach it. Charging Time and Available Recording Time A Charging Time B Maximum Continuous Recording Time ≥"1 h 20 min." indicates 1 hour and 20 minutes. ≥Battery CGR-D16 is supplied. ≥The hours shown in the table are approximate hours. The numeric characters in parentheses indicate the recording time when the LCD monitor is used. In actual use, the available recording time may be shorter in some cases. ≥The hours shown in the table are for continuous recording at a temperature of 68xF (20xC) and humidity of 60%. If the Battery is charged at a higher or lower temperature, the charging time may be longer. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
14
1
3
2
1
A
B
A
A
B
B
2 h.
3 h 15 min.
2 h 20 min.
(2 h.)
4 h 05 min.
(3 h 25 min.)
5 h 20 min.
7 h 40 min.
(6 h 25 min.)
CGR-D16
CGP-D28
CGR-D53
Power Supply
ª
Using the AC Adaptor
1
Insert the battery-shaped connector of the DC Cable into the
Battery Holder on the Palmcorder.
2
Connect the DC Cable to the [DC OUT] Jack on the AC
Adaptor.
3
Connect the AC Adaptor and AC Cable.
≥
The AC Cable’s outlet plug cannot be pushed fully into the AC Adaptor
Jack. A gap will remain as shown
1
.
≥
Before connecting or disconnecting the power supply, set the [OFF/
ON/MODE] Switch on the Palmcorder to [OFF] and make sure that
[CAMERA/VCR/CARD P.B.] Lamps are not lit.
≥
Battery cannot be charged if DC Cable is connected to AC Adapter.
ª
Using the Battery
Before use, fully charge the battery.
1
Attach the Battery to AC Adaptor and charge it.
≥
Since the Battery will not be charged when the DC Cable is connected
to the AC Adaptor, disconnect it.
≥
The [POWER] Lamp and [CHARGE] Lamp lights up, and charging
starts.
≥
When the [CHARGE] Lamp goes off, charging is completed.
2
Attach the charged Battery to the Palmcorder.
Disconnecting the Power Source
Set the [OFF/ON/MODE] Switch
1
to [OFF], and while pressing the
[PUSH BATT] Button
2
, slide the Battery or battery-shaped connector
upward to disconnect it.
≥
When attaching or removing battery, set [OFF/ON/MODE] Switch to
[OFF] and make sure the Operation Mode Lamp is not lit.
≥
When the Palmcorder is used for a long time, the Camera body becomes
warm, but this is not a malfunction.
≥
If the [CHARGE] Lamp does not light up, although the Battery is attached to
the AC Adaptor, detach the Battery and reattach it.
~~~~~~~~~~~~~~~~~~~~~~~~
Charging Time and Available Recording Time
A
Charging Time
B
Maximum Continuous Recording Time
≥
“1 h 20 min.” indicates 1 hour and 20 minutes.
≥
Battery CGR-D16 is supplied.
≥
The hours shown in the table are approximate hours. The numeric
characters in parentheses indicate the recording time when the LCD
monitor is used. In actual use, the available recording time may be shorter
in some cases.
≥
The hours shown in the table are for continuous recording at a temperature
of 68
x
F (20
x
C) and humidity of 60%. If the Battery is charged at a higher or
lower temperature, the charging time may be longer.
1
2
PUSH
BAT T
O
F
F
O
N
M
O
D
E
2
1