Samsung SPH700AE User Manual (ENGLISH) - Page 7

Front/Upper Side and Accessories

Page 7 highlights

Projector and Accessories Preparation PROJECTOR AND ACCESSORIES Front/Upper Side and Accessories Front/Upper Side 11 10 98 7 1 2 3 1 Indicators - TEMP (Red LED) - LAMP (Blue LED) - STAND BY (Blue LED) Refer to page 13 for details. 2 Remote Control Signal Receiver 3 Focus Ring Used for Focus Adjustment. 4 Lens 5 Adjustable Feet You can adjust the screen position by moving up and down the adjustable feet. 6 Zoom Knob Used to enlarge or reduce image size. 6 4 5 7 MENU Used to open the on-screen Menu. 8 POWER Used to turn the projector on or off. 9 SOURCE Used to select input signals from the external sources. 10 Select and Move Button Used to select an menu item, and to move the cursor. 11 LENS SHIFT Dial You can adjust screen images up and down within the lens range. Accessories Remote Control(BP59-00036A)/ 2 Batteries Power Cable (3903-000085) Owner's Instructions (including a warranty certificate) 12 Indicator Information : Turned On : Flashing : Turned Off TEMP LAMP STANDBY Information If you press the POWER button on the remote control or projector, the screen appears within 30 seconds. The projector is in normal operating condition. The projector is warming up after POWER button has been pressed. The POWER button is pressed to turn off the projector, and the cooling system is in operation to cool off inside of the projector. (Lasts for about 1 minute and 30 seconds) Refer to measure 1 below if the cooling fan inside the projector is not in normal operation condition. Refer to measure 2 below if the lamp cover protecting the lamp unit is not closed properly. Power is turned off automatically when temperature inside of the projector goes beyond the control limit. Refer to measure 3. Refer to measure 4 below if the life span of the lamp is running out or a problem with the lamp is detected. Clearing Indicator Problems Classification Measure 1 Measure 2 Measure 3 Measure 4 State Measures When the cooling fan system is Unplug and plug the cord and restart the projector. If the not in normal operating condition. problem does not disappear, contact a dealer or service personnel near you. When the lamp cover protecting the lamp unit is not properly closed or the sensor system is not in normal operating condition. Check the screw on the bottom side of the projector. If you do not find any problem, contact a dealer or service personnel near you. When temperature inside of the projector becomes too high. The lamp is malfunctioning after abnormal power off or restarting right after turning off the projector. Adjust the position of the projector following the installation instructions of this manual and cool off the projector before restarting it. If the problem does not disappear, contact a dealer or service personnel near you. Power off the projector and cool it off for some time before restarting it. When brightness of the picture screen degrades or image deterioration is found. Check how long the lamp has been used on Information and contact a dealer or service personnel near you for lamp replacement. This Projector uses a cooling fan system to keep the unit from overheating. NOTE Operation of the cooling fan may cause noise, which does not affect the product performance. No exchange or refund for the noise concern. 13 Projector and Accessories Preparation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42

Front/Upper Side
PROJECTOR AND ACCESSORIES
Front/Upper Side and Accessories
Preparation
Projector and Accessories
12
Preparation
Projector and Accessories
13
1
Indicators
-
TEMP (Red LED)
-
LAMP (Blue LED)
-
STAND BY (Blue LED)
Refer to page 13 for details.
2
Remote Control Signal Receiver
3
Focus Ring
Used for Focus Adjustment.
4
Lens
5
Adjustable Feet
You can adjust the screen position by moving
up and down the adjustable feet.
6
Zoom Knob
Used to enlarge or reduce image size.
7
MENU
Used to open the on-screen Menu.
8
POWER
Used to turn the projector on or off.
9
SOURCE
Used to select input signals from the external
sources.
10
Select and Move Button
Used to select an menu item, and to move the
cursor.
11
LENS SHIFT Dial
You can adjust screen images up and down
within the lens range.
Remote Control(BP59-00036A)/
2 Batteries
Power Cable
(3903-000085)
Owner's Instructions
(including a warranty certificate)
1
2
3
4
5
6
7
8
9
10
11
: Turned On
: Flashing
: Turned Off
STANDBY
LAMP
TEMP
Information
If you press the
POWER
button on the remote control or projector, the screen
appears within 30 seconds.
The projector is in normal operating condition.
The projector is warming up after
POWER
button has been pressed.
The
POWER
button is pressed to turn off the projector, and the cooling system is
in operation to cool off inside of the projector. (Lasts for about 1 minute and 30
seconds)
Refer to measure 1 below if the cooling fan inside the projector is not in normal
operation condition.
Refer to measure 2 below if the lamp cover protecting the lamp unit is not closed
properly.
Power is turned off automatically when temperature inside of the projector goes
beyond the control limit. Refer to measure 3.
Refer to measure 4 below if the life span of the lamp is running out or a problem
with the lamp is detected.
When the cooling fan system is
not in normal operating condition.
When the lamp cover protecting
the lamp unit is not properly
closed or the sensor system is not
in normal operating condition.
When temperature inside of the
projector becomes too high.
The lamp is malfunctioning after
abnormal power off or restarting
right after turning off the projector.
When brightness of the picture
screen degrades or image
deterioration is found.
Unplug and plug the cord and restart the projector. If the
problem does not disappear, contact a dealer or service
personnel near you.
Check the screw on the bottom side of the projector. If you
do not find any problem, contact a dealer or service
personnel near you.
Adjust the position of the projector following the
installation instructions of this manual and cool off the
projector before restarting it. If the problem does not
disappear, contact a dealer or service personnel near you.
Power off the projector and cool it off for some time before
restarting it.
Check how long the lamp has been used on Information
and contact a dealer or service personnel near you for lamp
replacement.
Measure 1
Measure 2
Measure 3
Measure 4
Indicator Information
Classification
State
Measures
Accessories
Clearing Indicator Problems
NOTE
This Projector uses a cooling fan system to keep the unit from overheating.
Operation of the cooling fan may cause noise, which does not affect the product performance.
No exchange or refund for the noise concern.