Home » Sony Manuals » Video Players » Sony DSR 45A » Manual Viewer

Sony DSR 45A Operating Instructions - Page 56

Adjusting Edit Timing

UPC - 027242689602

Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Chapter 3 Using the Unit as a Player in an Editing System Adjusting Edit Timing For details, refer to the instruction manuals of the editing controller you use. Using this unit as a player 1 with the FXE120/120P Using this unit as a player with the RM450/450CE 1 Set the SYNCHRO selector to ON. 2 Set item number 3 of the SYSTEM PRESET right switch to OFF (it is set to OFF at factory). Setting this to OFF adjusts the synchronization of the recorder. 3 Execute the LEARN function. Using this unit as player 1 with the PVE500 When using this unit as player 2, the relevant menu item is indicated in ( ). 1 Set Sync Edt of SEtUP-10 to OFF in the SETUP menu. 2 Set P1 dELAY (P2 dELAY) of SEtUP-13 (SEtUP- 14) to LEArn in the SETUP menu. 3 Set rEC Sync of SEtUP-15 to On in the SETUP menu. 4 Set P1 Sync (P2 Sync) of SEtUP-16 (SEtUP-17) to OFF in the SETUP menu. 5 Execute the LEARN function. • When using this unit as player 2, the relevant menu item is indicated in ( ). • When using an FXE-100/100P that has been upgraded with an FXE-KIT1, the relevant menu item is indicated in [ ]. 1 Display item 104 [301] SYNC GRADE in the SETUP menu, and set PLAYER1 (PLAYER2) to PREROLL & PLAY. 2 Display item 301 (302) [401 as player 1, 402 as player 2] DEVICE TYPE PLAYER1 (DEVICE TYPE PLAYER2) in the SETUP menu, and set the VCR device constants. For details on device constants, see page 47 (GB). 3 Execute the LEARN function. If the edit timing is out of adjustment, follow the instruction given in "Adjusting the IN point" below. Adjusting the IN point If the actual edited point does not accurately coincide with the preset editing point, perform a fine adjustment of the edit timing using the SETUP menu of the editing controller. This improves the editing accuracy. 1 Display item 301 (302) [401 as player 1, 402 as player 2] DEVICE TYPE PLAYER1 (DEVICE TYPE PLAYER2) in the SETUP menu, and change it from DISABLE to ENABLE. 2 Repeat the editing process several times and check the shift of the editing point; that is, count the number of frames to be adjusted. Note The editing results may differ between the DISABLE and ENABLE settings of SETUP menu item 301 (302) [401 as player 1, 402 as player 2]. Be sure to check the editing results after changing the setting to ENABLE. 56 (GB) Chapter 3 Using the Unit as a Player in an Editing System

Section	Page
GB	6
Chapter 1 Overview	9
Features	9
DVCAM Format	9
Other Features	11
Location and Function of Parts	12
Front Panel	12
Rear Panel	20
Supplied Remote Commander	25
Displaying Various Data	27
Chapter 2 Playback and Recording	30
Notes on Video Cassettes	30
Inserting/Ejecting Cassettes	31
Notes on Playback/Recording	32
Playback	33
Connections for Playback	33
Settings for Playback	35
Playback Procedures	35
Playback Functions	36
Recording	41
Connections for Recording	41
Settings for Recording	43
Recording Procedures	44
Recording Functions	44
Chapter 3 Using the Unit as a Player in an Editing System	46
Notes on Usage in the Editing System	46
Connections for Digital Non-linear Editing	48
Connections for a Cut Editing System	49
Connections for an A/B Roll Editing System	51
Adjusting Edit Timing	56
Chapter 4 Setting the Time Code and Adjusting the Video Signals	58
Setting the Time Code and User Bits	58
Using the Internal Time Code Generator	58
Synchronizing the Time Codes Synchronizing the Time Codes	62
Connecting to the Time Code Generator	62
Notes on the Time Codes	64
Adjusting the Sync and Subcarrier Phases of the Video Signals	66
Adjusting the Signals	68
Chapter 5 Duplication and Audio Dubbing	69
Duplication (generating a work tape with the same time code)	69
Audio Dubbing	74
Chapter 6 Adjusting and Setting Through Menus	76
Operating the Menus	76
Menu Organization	77
Menu Contents	78
Chapter 7 Maintenance	93
Troubleshooting	93
Alarm Messages	97
Notes on Use	98
Notes on the Videocassette Recorder	98
Cleaning of the Video Heads	98
Notes on the Video Cassettes	99
Notes on the LCD Screen	99
About Moisture Condensation	99
Digital Hours Meter	100
Self-diagnostics Function	100
Appendix	101
Compatibility of DVCAM and DV Format	101
Notes on Wide-screen Aspect Ratio Information	103
Specifications	104
Glossary	106
Index	108
Submenu Index	109
FR	112
Chapitre 1 Présentation	115
Caract é ristiques	115
Format DVCAM	115
Autres caract é ristiques	117
Emplacement et fonction des pi è ces	118
Panneau avant	118
Panneau arri è re	127
T é l é commande fournie	132
Affichage de diff é rentes donn é es	134
Chapitre 2 Lecture et enregistrement	137
Remarques sur les cassettes vid é o	137
Insertion/é jection de cassettes	138
Remarques sur la lecture et l ’enregistrement	139
Lecture	141
Raccordements pour la lecture	141
Configuration pour la lecture	143
Proc é dures pour la lecture	143
Fonctions de lecture	144
Enregistrement	149
Raccordements pour l ’enregistrement	149
Configuration pour l ’enregistrement	151
Proc é dures d ’enregistrement	152
Fonctions d ’enregistrement	152
Chapitre 3 Utilisation de l ’appareil comme lecteur dans un système de montage	154
Remarques sur l ’utilisation dans un syst è me de montage	154
Raccordements du montage non lin é aire num é rique	156
Raccordements pour un syst è me de montage de coupe	157
Raccordements du syst è me de montage en mode A/B	159
R é glage du temps de montage	164
Chapitre 4 Réglage du code temporel et ajustement des signaux vidéo	166
R é glage du code temporel et des bits d ’utilisateur	166
Utilisation du g é n é rateur de code temporel interne	166
Synchronisation des codes temporels	171
Raccordement au g é n é rateur de code temporel	171
Remarques sur les codes temporels	173
R é glage des phases de synchronisation et de sous-porteuse des signaux vid é o	175
R é glage des signaux	177
Chapitre 5 Copie et doublage audio	178
Copie (g é n é ration d ’une bande de travail avec le m ê me code temporel)	178
Doublage audio	183
Chapitre 6 Ajustement et réglage via les menus	185
Utilisation des menus	185
Organisation des menus	186
Contenu des menus	187
Chapitre 7 Entretien	202
D é pannage	202
Messages d ’alarmes	206
Remarques sur l ’utilisation	207
Remarques sur l ’enregistreur de cassettes vid é o	207
Nettoyage des t ê tes vid é o	208
Remarques sur les cassettes vid é o	208
Remarques sur l ’é cran à cristaux liquides	209
A propos de la condensation d ’humidit é	209
Compteur horaire num é rique	209
Fonction d ’autodiagnostics	210
Annexe	211
Compatibilit é des formats DVCAM et DV	211
Remarques concernant les informations du rapport d’aspect grand écran	213
Sp é cifications	214
Glossaire	217
Index	219

Match case Limit results 1 per page

Chapter 3

Using the Unit as a Player in an Editing System

(GB)

Chapter 3

Using the Unit as a Player in an Editing System

Adjusting Edit Timing

For details, refer to the instruction manuals of the editing

controller you use.

Using this unit as a player with the RM-

450/450CE

Set the SYNCHRO selector to ON.

Set item number 3 of the SYSTEM PRESET right

switch to OFF (it is set to OFF at factory).

Setting this to OFF adjusts the synchronization of

the recorder.

Execute the LEARN function.

Using this unit as player 1 with the PVE-

500

When using this unit as player 2, the relevant menu

item is indicated in ( ).

Set Sync Edt of SEtUP-10 to OFF in the SETUP

menu.

Set P1 dELAY (P2 dELAY) of SEtUP-13 (SEtUP-

14) to LEArn in the SETUP menu.

Set rEC Sync of SEtUP-15 to On in the SETUP

menu.

Set P1 Sync (P2 Sync) of SEtUP-16 (SEtUP-17) to

OFF in the SETUP menu.

Execute the LEARN function.

Using this unit as a player 1 with the FXE-

120/120P

• When using this unit as player 2, the relevant menu

item is indicated in ( ).

• When using an FXE-100/100P that has been

upgraded with an FXE-KIT1, the relevant menu item

is indicated in [ ].

Display item 104 [301] SYNC GRADE in the

SETUP menu, and set PLAYER1 (PLAYER2) to

PREROLL & PLAY.

Display item 301 (302) [401 as player 1, 402 as

player 2] DEVICE TYPE PLAYER1 (DEVICE

TYPE PLAYER2) in the SETUP menu, and set the

VCR device constants.

For details on device constants, see page 47 (GB).

Execute the LEARN function.

If the edit timing is out of adjustment, follow the

instruction given in “Adjusting the IN point”

below.

Adjusting the IN point

If the actual edited point does not accurately coincide

with the preset editing point, perform a fine adjustment

of the edit timing using the SETUP menu of the editing

controller. This improves the editing accuracy.

Display item 301 (302) [401 as player 1, 402 as

player 2] DEVICE TYPE PLAYER1 (DEVICE

TYPE PLAYER2) in the SETUP menu, and

change it from DISABLE to ENABLE.

Repeat the editing process several times and check

the shift of the editing point; that is, count the

number of frames to be adjusted.

Note

The editing results may differ between the

DISABLE and ENABLE settings of SETUP menu

item 301 (302) [401 as player 1, 402 as player 2].

Be sure to check the editing results after changing

the setting to ENABLE.