Sony KLV-21SG2 Operating Instructions - Page 13

Connecting a Satellite Receiver - remote

Get Sony KLV-21SG2 - 21inch Lcd Wega Television PDF manuals and user guides View all Sony KLV-21SG2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Installing and Connecting the TV Connecting a Satellite Receiver Disconnect all power sources before making any connections. 1 Connect the satellite antenna cable to the satellite receiver's SATELLITE IN jack. 2 Using AUDIO and S VIDEO cables, connect the satellite receiver's AUDIO and S VIDEO OUT jacks to the TV's AUDIO and S VIDEO IN jacks. 3 Connect the supplied 75-ohm coaxial cable from your cable or antenna to the TV's VHF/UHF jack. Rear of TV Satellite receiver 75-ohm coaxial cable (supplied) S VIDEO VIDEO (yellow) Satellite antenna cable AUDIO-L (white) AUDIO-R (red) S VIDEO cable (not supplied) AUDIO cable (not supplied) Note When you connect video equipment to both the VIDEO and the S VIDEO input jacks, make sure "Auto YC" in the (Setup) menu is set to "On" to view the S VIDEO input (see page 12). Tips • You can also use the VIDEO 2 IN jacks located on the left side of the TV to connect your satellite receiver. • If your satellite receiver is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable. • Use TV/VIDEO on the remote control to select VIDEO 1 IN (or VIDEO 2 IN if you use the VIDEO 2 IN jacks for this hookup) to watch satellite TV or to watch a tape on the VCR (your VCR must be turned on). 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
13
Installing and Connecting the TV
Connecting a Satellite Receiver
Disconnect all power sources before making any connections.
1
Connect the satellite antenna cable to the satellite receiver’s SATELLITE
IN jack.
2
Using AUDIO and S VIDEO cables, connect the satellite receiver’s AUDIO
and S VIDEO OUT jacks to the TV’s AUDIO and S VIDEO IN jacks.
3
Connect the supplied 75-ohm coaxial cable from your cable or antenna to the
TV’s VHF/UHF jack.
VIDEO (yellow)
AUDIO-L (white)
AUDIO-R (red)
S VIDEO
Rear of TV
75-ohm coaxial
cable (supplied)
Note
When you connect video equipment to both the VIDEO and the S VIDEO input jacks, make
sure “Auto YC” in the
(Setup) menu is set to “On” to view the S VIDEO input (see page
12).
Tips
•
You can also use the VIDEO 2 IN jacks located on the left side of the TV to connect your
satellite receiver.
•
If your satellite receiver is not equipped with S VIDEO, use a VIDEO cable (yellow)
instead of the S VIDEO cable.
•
Use TV/VIDEO on the remote control to select VIDEO 1 IN (or VIDEO 2 IN if you use the
VIDEO 2 IN jacks for this hookup) to watch satellite TV or to watch a tape on the VCR
(your VCR must be turned on).
S VIDEO cable
(not supplied)
AUDIO cable (not supplied)
Satellite
antenna
cable
Satellite receiver