Sony KLV-21SG2 Operating Instructions - Page 20

Setting the Channels

Get Sony KLV-21SG2 - 21inch Lcd Wega Television PDF manuals and user guides View all Sony KLV-21SG2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installing and Connecting the TV Setting the Channels After you finish connecting your TV, you can run Auto Program to set up your channels. The Auto Setup menu appears when you turn your TV on for the first time after installing it. To skip channels, see page 21. 1 2 1 Press I (power) on the TV. The Auto Setup menu automatically appears on the screen when you turn on the TV for the first time. Auto Setup I , Auto Program: Exit: [CH+] [CH-] First please connect cable/antenna 20 2 Press CH+ on the remote control or on the side panel of your TV to perform Auto Program. When all the receivable channels are stored, the "Channel Skip/Add" menu appears. Auto Program is set to scan cable TV channels by default. To watch UHF channels with an antenna, see "To watch UHF channels with an antenna" below. To perform Auto Program again 1 Press MENU. 2 Press V/v to select . (Channel), then press 3 Press V/v to select "Auto Program," then press . 4 Press "OK." "Auto Program" appears and the TV starts scanning and presetting channels automatically. When all the receivable channels are stored, the "Channel Skip/Add" menu appears. Using this menu, you can start skipping unwanted channels (see "To skip channels" on page 21). 5 Press MENU to exit the menu screen. To cancel Auto Program While "Auto Program" is displayed in step 3, press MENU on the remote control. Note To watch cable TV channels, you have to subscribe to a cable TV company. Note that cable TV cannot be received in some areas. This TV receives 1-125 cable TV channels. For details on cable TV subscription, consult your nearest cable TV company. To watch UHF channels with an antenna 1 Press MENU. 2 Press V/v to select . (Channel), then press 3 Press V/v to select "Cable," then press . 4 Press V/v to select "Off," then press . 5 Perform steps 3 - 5 in "To perform Auto Program again" above. Note You cannot receive and set the cable TV channels and UHF channels at the same time. Tip When you have a cable box or satellite receiver connected, the Channel Fix feature is useful. For details, see page 21.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
20
Installing and Connecting the TV
Setting the Channels
After you finish connecting your TV, you can run
Auto Program to set up your channels. The Auto
Setup menu appears when you turn your TV on for
the first time after installing it.
To skip channels, see page 21.
2
Press CH+ on the remote control or on the side
panel of your TV to perform Auto Program.
When all the receivable channels are stored, the
“Channel Skip/Add” menu appears.
Auto Program is set to scan cable TV channels by
default. To watch UHF channels with an antenna, see
“To watch UHF channels with an antenna” below.
To perform Auto Program again
1
Press MENU.
2
Press
V
/
v
to select
(Channel), then press
.
3
Press
V
/
v
to select “Auto Program,” then press
.
4
Press “OK.”
“Auto Program” appears and the TV starts
scanning and presetting channels automatically.
When all the receivable channels are stored, the
“Channel Skip/Add” menu appears. Using this
menu, you can start skipping unwanted channels
(see “To skip channels” on page 21).
5
Press MENU to exit the menu screen.
To cancel Auto Program
While “Auto Program” is displayed in step 3, press
MENU on the remote control.
Note
To watch cable TV channels, you have to subscribe to a cable
TV company. Note that cable TV cannot be received in some
areas. This TV receives 1-125 cable TV channels. For details on
cable TV subscription, consult your nearest cable TV company.
To watch UHF channels with an antenna
1
Press MENU.
2
Press
V
/
v
to select
(Channel), then press
.
3
Press
V
/
v
to select “Cable,” then press
.
4
Press
V
/
v
to select “Off,” then press
.
5
Perform steps 3 - 5 in “To perform Auto
Program again” above.
Note
You cannot receive and set the cable TV channels and UHF
channels at the same time.
Tip
When you have a cable box or satellite receiver connected, the
Channel Fix feature is useful. For details, see page 21.
1
Press
I
(power) on the TV.
The Auto Setup menu automatically appears on
the screen when you turn on the TV for the first
time.
I
,
Auto Setup
Auto Program:
[CH+]
Exit:
[CH–]
First please connect
cable/antenna
1
2