Sony KLV-21SG2 Operating Instructions - Page 17

Connecting a DVD Player with A/V Connectors

Get Sony KLV-21SG2 - 21inch Lcd Wega Television PDF manuals and user guides View all Sony KLV-21SG2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Installing and Connecting the TV Connecting a DVD Player with A/V Connectors Use this hookup if: • Your DVD player does not have component (Y, PB, PR) jacks. Tip If your DVD player has component video output connectors, for best picture quality, use the connection described on page 16. The Y, PB and PR jacks on your DVD player are sometimes labeled as Y, CB and CR, or Y, B-Y and R-Y. If so, connect the cables to the matching colors. Disconnect all power sources before making any connections. 1 Using an AUDIO cable, connect the DVD player's AUDIO OUT jacks to the TV's AUDIO IN jacks. 2 Using an S VIDEO cable, connect the DVD player's S VIDEO OUT jack to the TV's S VIDEO IN jack. Rear of TV S VIDEO cable (not supplied) AUDIO cable (not supplied) S VIDEO VIDEO (yellow) AUDIO-L (white) AUDIO-R (red) DVD player Note When you connect video equipment to both the VIDEO and the S VIDEO input jacks, make sure "Auto YC" in the (Setup) menu is set to "On" to view the S VIDEO input (see page 12). Tips • You can also use the VIDEO 2 IN jacks located on the left side of the TV to connect your DVD player. • To take advantage of the Wide Screen Modes, set the aspect ratio of the output signal to 16:9 on your DVD player. For details, refer to the operating instructions supplied with your DVD player. • Use TV/VIDEO on the remote control to switch to the DVD player input. • If your DVD player is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
17
Installing and Connecting the TV
Connecting a DVD Player with A/V Connectors
Use this hookup if:
•
Your DVD player does not have component (Y, P
B
, P
R
) jacks.
Tip
If your DVD player has component video output connectors, for best picture quality, use the
connection described on page 16.
The Y, P
B
and P
R
jacks on your DVD player are sometimes labeled as Y, C
B
and C
R
, or Y, B-Y
and R-Y. If so, connect the cables to the matching colors.
Disconnect all power sources before making any connections.
1
Using an AUDIO cable, connect the DVD player’s AUDIO OUT jacks to
the TV’s AUDIO IN jacks.
2
Using an S VIDEO cable, connect the DVD player’s S VIDEO OUT
jack to the TV’s S VIDEO IN jack.
Note
When you connect video equipment to both the VIDEO and the S VIDEO input jacks, make
sure “Auto YC” in the
(Setup) menu is set to “On” to view the S VIDEO input (see page
12).
Tips
•
You can also use the VIDEO 2 IN jacks located on the left side of the TV to connect your
DVD player.
•
To take advantage of the Wide Screen Modes, set the aspect ratio of the output signal to
16:9 on your DVD player. For details, refer to the operating instructions supplied with your
DVD player.
•
Use TV/VIDEO on the remote control to switch to the DVD player input.
•
If your DVD player is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of
the S VIDEO cable.
S VIDEO cable
(not supplied)
DVD player
AUDIO cable
(not supplied)
Rear of TV
S VIDEO
AUDIO-R
(red)
AUDIO-L
(white)
VIDEO (yellow)