Home » Sony Manuals » Webcams » Sony SNC-RS44N » Manual Viewer

Sony SNC-RS44N User Guide - Page 89

Configuring the Viewer — Viewer Menu, Layout tab, Viewer Menu

Get Sony SNC-RS44N - HD Network Rapid Dome Indoor 18X Optical Zoom PDF manuals and user guides

UPC - 027242254855

Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

• This camera does not correspond to the daisy chain connection of a VISCA device. Use the camera and the controller one-on-one. Baud rate Select a baud rate that corresponds to the peripheral device of serial interface. Selectable baud rates are shown below. 38400, 19200, 9600, 4800, 2400, 1200 (bps) Parity bit Select a parity that corresponds to the peripheral device connected to the serial interface: none, odd or even. Character length Select the character length that corresponds to the peripheral device connected to the serial interface: 7 or 8 (bits). Stop bits Select the stop bit that corresponds to the peripheral device connected to the serial interface: 1 or 2 (bits). OK/Cancel See "Buttons common to every menu" on page 29. Configuring the Viewer - Viewer Menu Click Viewer in the Administrator menu to display the Viewer menu. Using this menu, you can select the viewer to use and configure advanced settings. Layout tab Administrating the Camera Homepage Set the viewer or homepage to be displayed at the time of access. ActiveX Viewer Plug-in free Viewer 89 Configuring the Viewer - Viewer Menu

Section	Page
Table of Contents	2
Overview	4
Features	4
How to Use This User’s Guide	5
System Requirements	5
Preparation	6
Assigning the IP Address to the Camera	6
Assigning an IP address using SNC toolbox	6
When using Windows XP Service Pack 2 or later	8
When using Windows Vista	10
Accessing the Camera Using the Web Browser	13
Basic Configuration by the Administrator	15
Operating the Camera	16
Administrator and User	16
Logging in to System	17
Logging in as a user	17
About Viewers	17
Configuration of Main Viewer	18
Main menu	18
Control panel section	18
Monitor image	20
Plug-in free Viewer	20
Operating the Camera	21
Controlling via the control panel (Operation common to Area zoom mode and Vector dragging mode)	21
Panning and tilting by clicking the monitor image (Area zoom mode only)	22
Panning, tilting and zooming by specifying the area (Area zoom mode only)	22
Panning and tilting by dragging the screen (Vector dragging mode only)	22
Moving the camera to a preset position (Common operations in Area zoom and Vector dragging modes)	22
Controlling the Camera on a Panorama Image	23
Facing the camera toward a specified point	23
Using the Trigger Button	24
Sending a monitor image via e-mail	24
Sending a monitor image to an FTP server	24
Recording a camera image as a still image	24
Controlling alarm output 1, 2	24
Controlling the Day/Night function	24
Playing an audio file stored in the camera	24
Switching TCP/UDP Transmission Mode	25
Using the System Utility	26
SNC Viewer	26
SNC Desktop Viewer	27
Administrating the Camera	29
Basic Operations of the Administrator Menu	29
How to set up the Administrator menu	29
Configuration of the Administrator menu	30
Configuring the System — System Menu	31
System Tab	31
Date & time Tab	33
Superimpose Tab	34
Installation Tab	35
Initialize Tab	35
System log Tab	36
Access log Tab	36
Setting the Camera Image and Audio — Camera Menu	37
Common Tab	37
Picture Tab	38
Privacy Masking tab	40
Day/Night Tab	41
Video codec Tab	41
Streaming Tab	43
Configuring the Network — Network Menu	44
Network Tab	44
Wireless Tab — Setting of wireless connection	45
QoS Tab	48
Dynamic IP address notification Tab - Notifying the IP Address	49
Setting the SSL function — SSL Menu	51
SSL tab	51
CA certificate tab — Adding the CA certificate for client authentication	53
How to install the CA certificate	54
To remove an installed CA certificate	55
Using the 802.1X Authentication Function — 802.1X Menu	56
System configuration of 802.1X network	56
Common Tab — Basic setting of 802.1X authentication function	56
Client certificate Tab	57
CA certificate Tab	58
Setting the 802.1X authentication function — Example of Windows Server 2003	59
Setting the User — User Menu	62
Setting the Security — Security Menu	63
Saving the Camera Position and Action — Preset position Menu	63
Position Tab — Saving pan/tilt/ zoom position	63
Position Tour Tab — Setting a position tour	65
Shadow Tour Tab — Setting a shadow tour	66
Sending an Image via E- mail — e-Mail (SMTP) Menu	67
Common Tab — Setting the e-Mail (SMTP) Function	67
Alarm sending Tab — Setting the e- mail sending mode when detecting the alarm	68
Periodical sending Tab — Setting the periodical e-mail sending mode	69
Sending Images to FTP Server — FTP client Menu	70
Common Tab — Setting the FTP client function	70
Alarm sending Tab — Setting the FTP client action when detecting the alarm	70
Periodical sending Tab — Setting the periodical FTP client activity	71
Recording Images in Memory — Image memory Menu	72
Common Tab — Setting the image memory function	73
Alarm recording Tab — Setting the Image memory function when detecting the alarm	74
Periodical recording Tab — Setting the periodical recording mode	75
Folder structure of image memory	76
Downloading Images from the Camera — FTP server Menu	76
Setting the Alarm Output — Alarm output Menu	77
Alarm output 1, 2 Tab	77
Outputting Audio Linked to Alarm Detection — Voice alert Menu	78
Voice alert 1, 2, 3 Tab	78
Setting the Operations from the Viewer — Trigger Menu	79
Setting the Schedule — Schedule Menu	81
Setting the Alarm Buffer — Alarm buffer Menu	81
Setting the Motion Detection/VMF Function — Motion detection Menu	82
What are VMF functions	82
Setting items for motion detection	83
VMF setting items	85
Transmitting with External Equipment — PTZ control I/F Menu	88
Configuring the Viewer — Viewer Menu	89
Layout tab	89
HTML output tab	91
Others	92
Using the Supplied SNC toolbox	92
Starting SNC toolbox	92
How to use SNC toolbox	92
Registering in My device	94
Changing the Device list display method	95
Setting SNC toolbox options	96
Using Privacy Masking — Masking a Camera Image	97
Using Panorama Creator — Creating a Panorama Image	99
Using the Custom Homepage	100
Using the Firmware Upgrade	101
Using the Schedule Task	101
Configuring the device setting	103
Device restart and initialization	104
Using the SNC audio upload tool — Transmitting Audio to Camera	105
Installing the SNC audio upload tool	105
Connecting the Camera to the Computer	105
Using the SNC audio upload tool	106
Using the SNC video player — Playing a Video/Audio File Recorded with the Camera	110
Installing the SNC video player	110
Using the SNC video player	111
Assigning the IP Address to the Camera Using ARP Commands	112
Using the SNMP	112
1. Inquiry Commands	112
2. Setting Commands	113
Glossary	114