Adaptec LSM-FC2002 Installation Guide - Page 105

Appendix D: Upgrading a 2Gb SANbloc JBOD Array to a RAID Array, Equipment and parts necessary

Get Adaptec LSM-FC2002 - Loop Resiliency And SES Module Expansion PDF manuals and user guides
UPC - 760884145067
View all Adaptec LSM-FC2002 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

105 Appendix D: Upgrading a 2Gb SANbloc JBOD Array to a RAID Array In this section the procedure for upgrading a 2Gb SANbloc Series Storage Array from a JBOD system to a RAID system is described. The equipment and parts necessary for the upgrade are also described. Equipment and parts necessary for upgrade The following is a list of the equipment and parts required for the upgrade from JBOD to RAID: • Anti-static wrist strap and properly earthed grounding wire. • Phillips head screw driver. • 2Gb SANbloc RAID Controller (2 controllers if dual controller operation is required) • FC host cables to connect RAID controller to host/hub/switch Upgrading from JBOD to RAID CAUTION: Before beginning the upgrade, ensure that anti-static precautions are taken. The minimum requirement is an anti-static wrist strap and grounding wire. 1 Shut down the system and remove the power cables from the rear of the enclosure. 2 Using the Phillips head screwdriver, loosen the screws securing the I/O Module in the enclosure. 3 Using the handle on the module remove the I/O Module from the enclosure. 4 Into the I/O Module slot install the RAID controller and secure in place by tightening the screws using the Phillips head screw-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
105
Appendix D: Upgrading a 2Gb SANbloc
JBOD Array to a RAID Array
In this section the procedure for upgrading a 2Gb SANbloc
Series Storage Array from a JBOD system to a RAID system
is described. The equipment and parts necessary for the
upgrade are also described.
Equipment and parts
necessary for
upgrade
The following is a list of the equipment and parts required
for the upgrade from JBOD to RAID:
•
Anti-static wrist strap and properly earthed grounding wire.
•
Phillips head screw driver.
•
2Gb SANbloc RAID Controller (2 controllers if dual controller
operation is required)
•
FC host cables to connect RAID controller to host/hub/switch
Upgrading from
JBOD to RAID
CAUTION: Before beginning the upgrade, ensure that anti-static
precautions are taken. The minimum requirement is an anti-static
wrist strap and grounding wire.
1
Shut down the system and remove the power cables from the
rear of the enclosure.
2
Using the Phillips head screwdriver, loosen the screws securing
the I/O Module in the enclosure.
3
Using the handle on the module remove the I/O Module from the
enclosure.
4
Into the I/O Module slot install the RAID controller and secure
in place by tightening the screws using the Phillips head screw-