Adaptec LSM-FC2002 Installation Guide - Page 56

Single RAID Controller Configuration, Single RAID, Controller, Configuration

Get Adaptec LSM-FC2002 - Loop Resiliency And SES Module Expansion PDF manuals and user guides
UPC - 760884145067
View all Adaptec LSM-FC2002 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

56 Single RAID Controller Configuration In this configuration only one RAID controller is installed in the enclosure's I/O slot. The second I/O slot must contain an I/O module or a blank plate. Note: The following configuration procedures refer to connecting the 2Gb SANbloc Series directly to the host system. It is also possible to connect the system using a Hub/ Switch. CAUTION: Before working on the enclosure, ensure that antistatic precautions have been taken. The minimum requirement is an anti-static wrist strap and grounding wire. To connect this configuration to a host system, follow this procedure: Connecting a Single RAID Controller to a Host 1 Plug both host cables into the host connectors on the RAID controller (see Figure 4-5). Note: For single HBA configurations only one of the host connectors should be used. 2 Connect the opposite ends of these host cables, to the HBA's of the host system. Note: For details on your host and/or HBA refer to the documentation that was supplied with the host / HBA. Configurations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Configurations
56
Single RAID
Controller
Configuration
In this configuration only one RAID controller is installed in
the enclosure’s I/O slot. The second I/O slot must contain an
I/O module or a blank plate.
Note:
The following configuration procedures refer to
connecting the 2Gb SANbloc Series directly to the host
system. It is also possible to connect the system using a Hub/
Switch.
CAUTION: Before working on the enclosure, ensure that anti-
static precautions have been taken. The minimum requirement is
an anti-static wrist strap and grounding wire.
To connect this configuration to a host system, follow this
procedure:
Connecting a Single RAID Controller to a Host
1
Plug both host cables into the host connectors on the RAID
controller (see Figure 4-5).
Note:
For single HBA configurations only one of the host
connectors should be used.
2
Connect the opposite ends of these host cables, to the HBA’s of
the host system.
Note:
For details on your host and/or HBA refer to the documen-
tation that was supplied with the host / HBA.