Brother International BES-1260BC Instruction Manual - English - Page 223

Error, Measures, Hoop overhang +X, -X, +Y

Get Brother International BES-1260BC PDF manuals and user guides View all Brother International BES-1260BC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 223 highlights

Chapter 11 List of Error Codes Code E-02 E-03 E-04 E-05 E-06 E-07 E-08 E-09 E-0A E-14 E-18 E-21 E-22 E-23 E-24 E-25 E-26 E-27 E-28 E-29 E-2A E-2B E-2C E-2D E-2E E-2F Error Overtravel occurs during home position detecting movement. Measures Turn the power off once, then on again. If the same error occurs again, the area sensor is faulty. The stop switch is pressed during home Press and clear the error message. Pressing STOP START position detecting movement. restarts the home position detecting movement again. Zero detecting movement out of range Turn the power off once, then on again. If the same error occurs again, the X- or Y-axis mechanism is faulty. Needle stop position error Needle bar case position error Needle bar case lock Adjust the pulley stop position (100°) above the needle and press . STOP Press . If the error persists, the color-change STOP mechanism is faulty. Stop switch or emergency switch was pressed Press . STOP while the needle bar case is traveling. X-axis home position detection error Thread breakage error Y-axis home position detection error Turn the power off once, then on again. If the same error occurs again, the X-axis mechanism is faulty. After passing through the thread, press . STOP Turn the power off once, then on again. If the same error occurs again, the Y-axis mechanism is faulty. X-axis stepping motor connector error Hoop overhang (+X) Hoop overhang (+Y) Hoop overhang (+X, +Y) Hoop overhang (-X) Hoop overhang (+X, -X) Hoop overhang (-X, +Y) Hoop overhang (+X, -X, +Y) Hoop overhang (-Y) Hoop overhang (+X, -Y) Hoop overhang (+Y, -Y) Hoop overhang (+X, +Y, -Y) Hoop overhang (-X, -Y) Hoop overhang (+X, -X, -Y) Hoop overhang (-X, +Y, -Y) Hoop overhang (+X, -X, +Y, -Y) Check that the connector of the X-axis stepping motor is properly connected, and press . STOP Set the embroidering area again on the personal computer or move the hoop to a sewable position. (The hoop can be moved to a sewable position by pressing .) 228 BES-960BC • BES-1260BC

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
BES-960BC
•
BES-1260BC
228
Chapter 11
List of Error Codes
E-02
E-03
E-04
E-05
E-06
E-07
E-08
E-09
E-0A
E-14
E-18
E-21
E-22
E-23
E-24
E-25
E-26
E-27
E-28
E-29
E-2A
E-2B
E-2C
E-2D
E-2E
E-2F
Overtravel occurs during home position
detecting movement.
The stop switch is pressed during home
position detecting movement.
Zero detecting movement out of range
Needle stop position error
Needle bar case position error
Needle bar case lock
Stop switch or emergency switch was pressed
while the needle bar case is traveling.
X-axis home position detection error
Thread breakage error
Y-axis home position detection error
X-axis stepping motor connector error
Hoop overhang (+X)
Hoop overhang (+Y)
Hoop overhang (+X, +Y)
Hoop overhang (-X)
Hoop overhang (+X, -X)
Hoop overhang (-X, +Y)
Hoop overhang (+X, -X, +Y)
Hoop overhang (-Y)
Hoop overhang (+X, -Y)
Hoop overhang (+Y, -Y)
Hoop overhang (+X, +Y, -Y)
Hoop overhang (-X, -Y)
Hoop overhang (+X, -X, -Y)
Hoop overhang (-X, +Y, -Y)
Hoop overhang (+X, -X, +Y, -Y)
Turn the power off once, then on again.
If the same
error occurs again, the area sensor is faulty.
Press
STOP
and clear the error message.
Pressing
START
restarts the home position detecting movement again.
Turn the power off once, then on again.
If the same error
occurs again, the X- or Y-axis mechanism is faulty.
Adjust the pulley stop position (100
°
) above the needle
and press
STOP
.
Press
STOP
.
If the error persists, the color-change
mechanism is faulty.
Press
STOP
.
Turn the power off once, then on again.
If the same
error occurs again, the X-axis mechanism is faulty.
After passing through the thread, press
STOP
.
Turn the power off once, then on again.
If the same
error occurs again, the Y-axis mechanism is faulty.
Check that the connector of the X-axis stepping motor
is properly connected, and press
STOP
.
Set the embroidering area again on the personal
computer or move the hoop to a sewable position.
(The
hoop can be moved to a sewable position by pressing
.)
Code
Error
Measures