Brother International BES-963 Instruction Manual - English - Page 164
Error Messages, home position just after the power is turned on. - area code
View all Brother International BES-963 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 164 highlights
Chapter 9 Error code list Code Error Messages Error Measures E-00 E-01 E-02 E-03 E-04 E-05 E-06 E-07 E-08 E-09 E-0A E-0B ERROR 00 No error occurs. This is not usually displayed. ERROR 01 Overtravel Stop SW was pressed during home positioning Zero positioning is out of range Needle stop position error Either motor of main shaft, X- or Y-axis, or lower shaft has locked. Overtravel occurs during home position detecting movement. The stop switch is pressed during home position detecting movement. Zero detecting movement out of range Needle stop position error This is not usually displayed. Turn the power off and on once. If the same error occurs again, the area sensor is faulty. Press the or turn on the F/B switch on the head to either STOP side to restart the home position detecting movement again. Turn the power off and on once. If the same error occurs again, the home position sensor is faulty. Adjust the pulley stop position (100 degrees) above the needle and press the or turn on the F/B switch on the STOP head to either side. Needle bar case position error Needle bar case position error This is not usually displayed. Needle case lock Stop while needle bar case transferring X-axis home position error Thread breakage error Needle bar case lock Stop switch or emergency switch was pressed while the needle bar case is traveling. X-axis home position detection error Thread breaking error Press the or turn on the F/B switch on the head to either STOP side. If the same error occurs again, the color change mechanism is faulty. This is not usually displayed. Turn the power off and on once. If the same error occurs again, the X-axis mechanism is faulty. After passing through the thread, press the or turn on the STOP F/B switch on the head to either side. ERROR 0B Stop or emergency stop during sewing This is not usually displayed. E-0C ERROR 0C Insufficient bobbin thread This is not usually displayed. E-0D ERROR 0D The machine does not return to the home position. This is not usually displayed. E-0E ERROR 0E Mending finish This is not usually displayed. E-0F E-14 E-15 E-16 E-17 E-18 E-1A E-1B E-1C E-1D E-1E E-1F ERROR 0F Undefined error This is not usually displayed. Y-axis home position error Press for reatart. ERROR 16 Y-axis home position error Stop error during SSP processing (when pressing the stop key while the hoop is moving) Needle with specified number is out of movable area. Turn the power off and on once. If the same error occurs again, the Y-axis mechanism is faulty. Hoop movement restarts if you press . This is not usually displayed. ERROR 17 Speed Vol. No. is out of range. This is not usually displayed. X-axis stepping motor connector X-axis stepping motor connector error error Turn the power off and on once after checking to see that the connector of the X-axis stepping motor is properly connected. ERROR 1A Destination coordinates error This is not usually displayed. ERROR 1B Restart perimeter Stop while transferring to next repeat pattern The machine has reached the mending stop position. The machine stops during mask tracing. The machine stops while the needle is moving between patterns during repeat sewing. This is not usually displayed. Tracing is cancelled if the key is pressed when the maSTOP chine is stopped during mask tracing. Press the key to continue tracing. This is displayed when the stop switch is pressed while the hoop is moving. Press the to move the hoop again. (It is necessary to press the again to start sewing.) Errors E-1C and E-1D are not displayed due to mechanical problems. Remove unused presser foot, or it may be damaged Presser foot down error When the power is turned on, bed can not be retracted. Presser foot down error while searching for home position just after the power is turned on. This is displayed when every other head control is selected or when the bed is retreated (including when the power is turned on). Remove the presser foot of the retreating head and press the return key or turn the F/B switch of the head to either side. If every other head control is not selected or the bed is not retreated, the bed sensor position may be faulty. Readjust it. Press the key. If the same error occurs STOP again, adjust it with the presser foot switch. Press the or turn on the F/B switch on the head to eiSTOP ther side. If the same error occurs again, adjust the presser foot switch. 162 BES-963BC • BES-1263BC