Brother International BES-963 Instruction Manual - English - Page 166
ERROR BB, BF, Power supply frequency error
View all Brother International BES-963 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 166 highlights
Chapter 9 Error code list Code Error Messages Error Measures E-A5 ERROR A5 E-A6 ERROR A6 E-A7 ERROR A7 E-A8 ERROR A8 E-A9 Spindle CPU parameter error E-B0 Lower shaft CPU error Spindle motor CPU error Spindle motor CPU communication command This is not usually displayed. error Spindle motor CPU send/receive error Spindle stop position signal error Adjust the pulley stop position (100 degrees) above the needle and press the . If the error occurs frequently, the parts STOP related to the main shaft stop position sensor are faulty. Spindle CPU parameter error Lower shaft CPU error This is not usually displayed. E-B1 Thread jammed in rotary hook Thread tangle in rotary hook E-B2 Hook motor origin point error Hook motor origin point error E-B3 Hook motor standby position error Hook motor standby position error E-B4 Hook motor standby position error Hook motor motor mode error Check to see that no lint is tangled in the rotary hook and press the or turn on the F/B switch on the head to either side. STOP The rotary hook may be rotated forcefully. Press the or STOP turn on F/B switch on the head to either side to cancel the error. If the same error occurs again, the lower shaft sensor is improperly adjusted. E-B5 Hook motor communication error Hook motor communication error This is not usually displayed. E-B6 Hook motor parameter error Hook motor parameter error E-B7 E-B8 E-B9 E-BA Hook motor overheat error Hook motor overheat error Hook motor overcurrent error Turn off the power Thread trimming motor origin point error Hook motor overcurrent error Thread trimming motor zero point error Power supply frequency error Power supply frequency error E-BC No power error No power error E-BD Lower shaft flash memory error Lower shaft flash memory error E-BE Lower shaft version-up error Lower shaft version-up error E-BB, BF ERROR BB, BF Lower shaft motor undefined error Turn the power off and on once. If the same error occurs again, the lower shaft motor is faulty. Turn the power off and check the thread trimmer and turn the power on again. If it occurs again, the thread trimmer is faulty. Turn the power off and on once. If the same error occurs again, the power PCB or power supply is faulty. It may usually occur momentarily when turning off the machine. If it occurs when the machine is on, it is a power failure detection error. Turn the power off and on once. If the same error occurs again, the main PCB is faulty. Press the or turn on the F/B switch on the head to either STOP side to cancel the error and upgrade the version again. This is not usually displayed. E-C1 ERROR C1 E-C2 Wiper out error E-C3 ERROR C3 E-C4 Presser foot down error E-C5 ERROR C5 E-C6 ERROR C6 E-C7 ERROR C7 E-C8 ERROR C8 E-C9 Embroidering start error E-CA ERROR CA Area over during embroidering Set the embroidering area again on the panel. Wiper out error If the wiper is tangled with a thread, remove it. Press the STOP or turn on the F/B switch on the head to either side. Embroidering data buffer empty This is not usually displayed. Presser foot down error Measured voltage value could not be received form the lower shaft motor CPU. Voltage value could not be transferred to the lower shaft motor CPU. Lower shaft error Hook motor origin point error Press the or turn on the F/B switch on the head to eiSTOP ther side. If the same error occurs again, adjust the presser foot switch. This is not usually displayed. The machine may be being tested in the BC test mode. Exit the test mode or turn the power off and on once. If the same error occurs again, the main PCB is faulty. Check the operation of the main shaft brake and the stop position of the main shaft (100 degrees). Embroidering start error No sewing permisson This is not usually displayed. 164 BES-963BC • BES-1263BC