Brother International Innov-is 40e Operation Manual - Page 107

sewn with

Get Brother International Innov-is 40e PDF manuals and user guides View all Brother International Innov-is 40e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

Symptom Probable Cause Remedy Reference The thread does not pass through the eye of the needle. The needle was not raised. The needle is incorrectly installed. Press (needle position button) once or twice to raise the needle. Correctly install the needle. page 20 page 29 The stitch is not sewn correctly. The appropriate presser foot for the Attach the presser foot that is type of stitch that you wish to sew is appropriate for the type of stitch that page 86 not used. you wish to sew. The thread tension is incorrectly set. Adjust the thread tension. page 47 The thread is tangled, for example, in the bobbin case. Remove the tangled thread. If the thread is tangled in the bobbin case, clean the race. page 90 The feed dogs are lowered. Slide the feed dog position switch to . page 74 The stitch is too short. Lengthen the stitch length. page 40 The fabric does not feed. The combination of fabric, thread and needle is incorrect. Select a thread and needle that are appropriate for the type of fabric being sewn. page 28 The thread is tangled, for example, in the bobbin case. Remove the tangled thread. If the thread is tangled in the bobbin case, clean the race. page 90 4 While winding the bobbin, the bobbin thread was wound below the bobbin You have not wound the bobbin thread properly. After removing the thread wound below the bobbin winder seat, wind the page 100 bobbin correctly. winder seat. Bobbin thread does not wind neatly on the bobbin. The thread is not passed through the Correctly pass the thread through the bobbin-winding thread guide correctly. bobbin-winding thread guide. page 15 Bobbin spins slowly. Move the sewing speed controller to the right (so that the speed will be fast). page 17 The thread that was pulled out was not wound onto the bobbin correctly. Wind the thread that was pulled off round the bobbin five or six times clockwise. page 17 Fabric being sewn with the machine cannot be removed. Thread is tangled below the needle plate. Lift up the fabric and cut the threads below it, and clean the race. page 97 The fabric feeds in the opposite The feed mechanism is damaged. direction. Contact your dealer or the nearest authorized service center. - The upper thread The bobbin thread is incorrectly has tightened up. installed. Correctly install the bobbin thread. page 18, 93 The thread is tangled on the wrong side of the fabric. You have not threaded the upper thread properly. Correct the upper threading. page 20, 94 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
105
4
The thread does
not pass through
the eye of the
needle.
The needle was not raised.
Press
(needle position button)
once or twice to raise the needle.
page 20
The needle is incorrectly installed.
Correctly install the needle.
page 29
The stitch is not
sewn correctly.
The appropriate presser foot for the
type of stitch that you wish to sew is
not used.
Attach the presser foot that is
appropriate for the type of stitch that
you wish to sew.
page 86
The thread tension is incorrectly set.
Adjust the thread tension.
page 47
The thread is tangled, for example, in
the bobbin case.
Remove the tangled thread. If the
thread is tangled in the bobbin case,
clean the race.
page 90
The fabric does
not feed.
The feed dogs are lowered.
Slide the feed dog position switch to
.
page 74
The stitch is too short.
Lengthen the stitch length.
page 40
The combination of fabric, thread and
needle is incorrect.
Select a thread and needle that are
appropriate for the type of fabric
being sewn.
page 28
The thread is tangled, for example, in
the bobbin case.
Remove the tangled thread. If the
thread is tangled in the bobbin case,
clean the race.
page 90
While winding
the bobbin, the
bobbin thread
was wound
below the bobbin
winder seat.
You have not wound the bobbin thread
properly.
After removing the thread wound below
the bobbin winder seat, wind the
bobbin correctly.
page 100
Bobbin thread
does not wind
neatly on the
bobbin.
The thread is not passed through the
bobbin-winding thread guide correctly.
Correctly pass the thread through the
bobbin-winding thread guide.
page 15
Bobbin spins slowly.
Move the sewing speed controller to the
right (so that the speed will be fast).
page 17
The thread that was pulled out was not
wound onto the bobbin correctly.
Wind the thread that was pulled off
round the bobbin five or six times
clockwise.
page 17
Fabric being
sewn with the
machine cannot
be removed.
Thread is tangled below the needle
plate.
Lift up the fabric and cut the threads
below it, and clean the race.
page 97
The fabric feeds
in the opposite
direction.
The feed mechanism is damaged.
Contact your dealer or the nearest
authorized service center.
–
The upper thread
has tightened up.
The bobbin thread is incorrectly
installed.
Correctly install the bobbin thread.
page 18,
93
The thread is
tangled on the
wrong side of the
fabric.
You have not threaded the upper thread
properly.
Correct the upper threading.
page 20, 94
Symptom
Probable Cause
Remedy
Reference