Brother International Innov-is NQ1300PRW Operation Manual - Page 26

Installing the bobbin

Get Brother International Innov-is NQ1300PRW PDF manuals and user guides View all Brother International Innov-is NQ1300PRW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Winding/Installing the Bobbin Press the "Start/Stop" button once to start winding the n bobbin. When the foot controller is plugged in, press down on the foot controller. Installing the bobbin Install the bobbin wound with thread. You can begin sewing immediately without pulling up the bobbin thread by simply inserting the bobbin in the bobbin case and guiding the thread through the slit in the needle plate cover. 1 1 "Start/Stop" button When the bobbin winding becomes slow, press the o "Start/Stop" button once to stop the machine. When the foot controller is plugged in, remove your foot from the foot controller. CAUTION • When the bobbin winding becomes slow, stop the machine, otherwise the machine may be damaged. Use scissors to cut the end of the thread wound around p the bobbin. Slide the bobbin winder shaft to the left, and then q remove the bobbin from the shaft. Memo • For details on sewing after pulling up the bobbin thread, for example, when making gathers or with free motion quilting, refer to "Pulling up the bobbin thread" on page B-24. CAUTION • Use a bobbin that has been correctly wound with thread, otherwise the needle may break or the thread tension will be incorrect. • Before inserting or changing the bobbin, be sure to press (Presser foot/Needle exchange key) on the operation panel to lock all keys and buttons, otherwise injuries may occur if the "Start/Stop" button or any other button is pressed and the machine starts. Press (Needle position button) once or twice to a raise the needle, and then lower the presser foot lever. Press b • If . is pressed while the presser foot is raised, an error message appears. Lower the presser foot. → The screen changes, and all keys and operation buttons are locked (except ). Memo • If the bobbin winder shaft is set to the right side, the needle will not move. (Sewing is impossible.) Slide the sewing speed controller back to desired r sewing speed position. Remove the spool for the bobbin thread from the spool s pin. Memo • When the machine is started or the handwheel is turned after winding the bobbin, the machine will make a clicking sound; this is not a malfunction. Raise the presser foot lever. c Slide the bobbin cover latch to the right. d 1 2 B-18 1 Bobbin cover 2 Latch

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Winding/Installing the Bobbin
B-18
n
Press the “Start/Stop” button once to start winding the
bobbin.
When the foot controller is plugged in, press down on
the foot controller.
1
“Start/Stop” button
o
When the bobbin winding becomes slow, press the
“Start/Stop” button once to stop the machine.
When the foot controller is plugged in, remove your
foot from the foot controller.
p
Use scissors to cut the end of the thread wound around
the bobbin.
q
Slide the bobbin winder shaft to the left, and then
remove the bobbin from the shaft.
r
Slide the sewing speed controller back to desired
sewing speed position.
s
Remove the spool for the bobbin thread from the spool
pin.
Installing the bobbin
Install the bobbin wound with thread.
You can begin sewing immediately without pulling up the
bobbin thread by simply inserting the bobbin in the bobbin
case and guiding the thread through the slit in the needle
plate cover.
a
Press
(Needle position button) once or twice to
raise the needle, and then lower the presser foot lever.
b
Press
.
• If
is pressed while the presser foot is raised, an
error message appears. Lower the presser foot.
→
The screen changes, and all keys and operation
buttons are locked (except
).
c
Raise the presser foot lever.
d
Slide the bobbin cover latch to the right.
1
Bobbin cover
2
Latch
CAUTION
•
When the bobbin winding becomes slow, stop
the machine, otherwise the machine may be
damaged.
Memo
•
If the bobbin winder shaft is set to the right side,
the needle will not move. (Sewing is impossible.)
Memo
•
When the machine is started or the handwheel is
turned after winding the bobbin, the machine will
make a clicking sound; this is not a malfunction.
1
Memo
•
For details on sewing after pulling up the bobbin
thread, for example, when making gathers or with
free motion quilting, refer to “Pulling up the
bobbin thread” on page B-24.
CAUTION
•
Use a bobbin that has been correctly wound
with thread, otherwise the needle may break
or the thread tension will be incorrect.
•
Before inserting or changing the bobbin, be
sure to press
(Presser foot/Needle
exchange key) on the operation panel to lock
all keys and buttons, otherwise injuries may
occur if the “Start/Stop” button or any other
button is pressed and the machine starts.
2
1