Brother International Innov-is NQ3700D Operation Manual - Page 111
List of symptoms
View all Brother International Innov-is NQ3700D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 111 highlights
Troubleshooting List of symptoms Check the following possible problems before requesting service. If the reference page is "*", contact your authorized Brother dealer or the nearest Brother authorized service center. ■ Getting ready Symptom, Cause/solution Reference Cannot thread the needle. Needle is not in the correct position. 10 • Press the "Needle position" button to raise the needle. Needle is installed incorrectly. 28 Needle is turned, bent or the point is dull. 28 Upper threading is incorrect. 24 The needle threader lever is not lowered until it clicks. The needle threader hook is bent and does not * pass through the eye of the needle. The needle threader lever cannot be moved or * returned to its original position. A size 65/9 needle is being used. 25 • The needle is incompatible with the needle threader. Manually pass the thread through the eye of the needle. Cannot lower the presser foot with the presser foot lever. Presser foot was raised using the "Presser foot 10 lifter" button. Bobbin thread does not wind neatly on the bobbin. The thread is not passed through the bobbin 20 winding thread guide correctly. The thread that was pulled out from the bobbin 21 winding thread guide was incorrectly wound onto the bobbin. The empty bobbin was not set on the pin properly. 20 While winding the bobbin, the bobbin thread was wound below the bobbin winder seat. The thread was incorrectly passed under the pretension disk on the bobbin winding thread guide. • Remove any entangled thread, and then wind the bobbin. 20, 108 The bobbin thread cannot be pulled up. Needle is turned, bent or the point is dull. 28 Bobbin is set incorrectly. 22 Nothing appears in the LCD. Main power switch is not turned on. 12 The plug of the power cord is not inserted into an 12 electrical outlet. The LCD screen is fogged up. Condensation has formed on the LCD screen. - • After a while, the cloudiness will disappear. Symptom, Cause/solution Reference The operation keys do not respond, or the key response is too sensitive. A glove is worn when the keys are pressed. The keys are pressed with a fingernail. A non-electrostatic touch pen is being used. The sensitivity of the operation keys is not set for the user. The sewing light does not come on. 13, 17 [Light] is set to [OFF] in the settings screen. 16 Embroidery unit does not operate. Embroidery unit is not attached correctly. 80 Embroidery frame was attached before the unit 80 was initialized. Cannot retrieve an embroidery pattern via wireless network. Embroidery patterns unavailable for this machine - cannot be retrieved. • Check the embroidery data and the message displayed on the application. ■ While sewing Symptom, Cause/solution Reference Machine does not operate. "Start/Stop" button was not pressed. 31 The bobbin winder shaft is pushed to the right. 20 There is no stitch selected. 31 Presser foot is not lowered. 32 "Start/Stop" button was pressed with the foot controller attached. The "Start/Stop" button was pressed while the machine is set for the sewing speed controller to control the zigzag stitch width. Needle breaks. Needle is installed incorrectly. 32 15, 66 28 Needle clamp screw is not tightened. 28 Needle is turned or bent. 28 Using improper needle or thread for the selected 27 fabric. Wrong presser foot was used. 29 Upper thread tension is too tight. 38 Fabric is pulled during sewing. - Spool of thread is set incorrectly. 20 There are scratches around the opening in the * needle plate. * There is a notch on the left side of the opening in the needle plate. This is not a scratch. a 1 Notch APPENDIX 5 There are scratches around the opening in the * presser foot. There are scratches on the bobbin case. * 109