Brother International Innov-is NQ3700D Operation Manual - Page 62

to check

Get Brother International Innov-is NQ3700D PDF manuals and user guides View all Brother International Innov-is NQ3700D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Utility Stitches Using a basting stitch, continue sewing to the edge of c the fabric. a b 1 Basting stitching 2 Wrong side of fabric Press open the seam allowance from the wrong side of d the fabric. 1 Wrong side of fabric 1 CAUTION • When using zipper foot "I", be sure to select the straight stitch (middle (center) needle position), and slowly turn the handwheel toward you (counterclockwise) to check that the needle does not touch the presser foot. If a different stitch is selected or the needle hits the presser foot, the needle may bend or break. Topstitch around the zipper. i Align the seam with the center of the zipper, and then e baste the zipper in place to the seam allowance. 1 Wrong side of fabric 2 Basting stitching 2 3 Zipper 1 3 Remove about 5 cm (2 inches) from the end of the f basting on the outside. 2 4 3 1 1 Wrong side of fabric 2 Zipper basting 3 Outside basting 4 5 cm (2 inches) Attach the presser foot holder to the right pin of zipper g foot "I". I 1 1 Pin on the right side 2 Needle drop point 2 1 3 2 4 1 Stitching 2 Right side of fabric 3 Basting stitching 4 End of zipper opening CAUTION • When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break. Memo • If the presser foot contacts the zipper slider, leave the needle lowered (in the fabric) and raise the presser foot. After moving the slider so it will not contact the presser foot, lower the presser foot and continue sewing. Remove the basting stitching. j Select a stitch. h No. 1-03 Stitch • For details, refer to "Stitch Chart" on page 45. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Utility Stitches
60
c
Using a basting stitch, continue sewing to the edge of
the fabric.
d
Press open the seam allowance from the wrong side of
the fabric.
e
Align the seam with the center of the zipper, and then
baste the zipper in place to the seam allowance.
f
Remove about 5 cm (2 inches) from the end of the
basting on the outside.
g
Attach the presser foot holder to the right pin of zipper
foot “I”.
h
Select a stitch.
•
For details, refer to “Stitch Chart” on page 45.
i
Topstitch around the zipper.
1
Stitching
2
Right side of fabric
3
Basting stitching
4
End of zipper opening
j
Remove the basting stitching.
1
Basting stitching
2
Wrong side of fabric
1
Wrong side of fabric
1
Wrong side of fabric
2
Basting stitching
3
Zipper
1
Wrong side of fabric
2
Zipper basting
3
Outside basting
4
5 cm (2 inches)
1
Pin on the right side
2
Needle drop point
No.
1-03
Stitch
a
b
1
1
2
3
4
1
2
3
2
1
I
CAUTION
•
When using zipper foot “I”, be sure to select
the straight stitch (middle (center) needle
position), and slowly turn the handwheel
toward
you (
counterclockwise)
to check that
the needle does not touch the presser foot. If a
different stitch is selected or the needle hits
the presser foot, the needle may bend or
break.
CAUTION
•
When sewing, be sure that the needle does not
touch the zipper, otherwise the needle may
bend or break.
Memo
•
If the presser foot contacts the zipper slider, leave
the needle lowered (in the fabric) and raise the
presser foot. After moving the slider so it will not
contact the presser foot, lower the presser foot and
continue sewing.
1
2
3
4