Canon imagePROGRAF iPF770 MFP M40 Basics Guide - Page 81

Adjusting Line Length, B:Standard/Draft

Get Canon imagePROGRAF iPF770 MFP M40 PDF manuals and user guides View all Canon imagePROGRAF iPF770 MFP M40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Adjustments for Better Print Quality iPF770 Series Adjusting Line Length 7 Press ▲ or ▼ to select Automatic, Print Quality, or Print Length, and then press the OK button. Adjusting Line Length To ensure that lines in CAD drawings are printed at exactly the right length, use Adjust Length to adjust the amount that paper is advanced. There are two options in Adjust Length : AdjustmentPrint and Change Settings. • AdjustmentPrint After a test pattern is printed, you will measure the discrepancy based on the results of printing. • Change Settings No test pattern is printed. Instead, you will measure a document already printed to determine the discrepancy. Additionally, two modes are available in both AdjustmentPrint and Change Settings : A:High or B:Standard/ Draft. Choose the mode that suits your particular printing application. • A:High This setting is applied when Highest or High is selected in Print Quality in the printer driver. • B:Standard/Draft This setting is applied when Standard or Fast is selected in Print Quality in the printer driver. • Always check the Adj. Priority values before using Adjust Length. (See "Selecting a Feed Amount Adjustment Note Method.") ➔P.80 • Use paper of the same type and size for adjustment as you will use for printing. Paper to Prepare When Using Rolls When Using Sheets • An unused roll at least 10 inches wide • High-precision ruler • One sheet of unused paper of at least A4/Letter size • High-precision ruler Perform adjustment as follows. 1 Load the paper. • Attaching the Roll Holder to Rolls ➔P.12 • Loading Rolls in the Printer ➔P.14 • Loading Sheets in the Printer ➔P.20 • Always make sure the loaded paper matches the type of paper specified. Adjustment cannot be com- Important pleted correctly unless the loaded paper matches the settings. 2 On the Tab Selection screen of the Control Panel, press ◀ or ▶ to select the Settings/Adj. tab ( ). Adjusting the feed amount • If the Tab Selection screen is not displayed, press the Menu button. Note 3 Press the OK button. 81 The Set./Adj. Menu is displayed. Basic Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
7
Press
▲
or
▼
to select
Automatic
,
Print Quality
, or
Print Length
, and then press the
OK
button.
Adjusting Line Length
Adjusting Line Length
To ensure that lines in CAD drawings are printed at exactly the right length, use
Adjust Length
to adjust the
amount that paper is advanced.
There are two options in
Adjust Length
:
AdjustmentPrint
and
Change Settings
.
•
AdjustmentPrint
After a test pattern is printed, you will measure the discrepancy based on the results of printing.
•
Change Settings
No test pattern is printed. Instead, you will measure a document already printed to determine the discrepancy.
Additionally, two modes are available in both
AdjustmentPrint
and
Change Settings
:
A:High
or
B:Standard/
Draft
. Choose the mode that suits your particular printing application.
•
A:High
This setting is applied when
Highest
or
High
is selected in
Print Quality
in the printer driver.
•
B:Standard/Draft
This setting is applied when
Standard
or
Fast
is selected in
Print Quality
in the printer driver.
Note
•
Always check the
Adj. Priority
values before using
Adjust Length
.
(See "Selecting a Feed Amount Adjustment
Method.")
➔
P.80
•
Use paper of the same type and size for adjustment as you will use for printing.
Paper to Prepare
When Using Rolls
•
An unused roll at least 10 inches wide
•
High-precision ruler
When Using Sheets
•
One sheet of unused paper of at least A4/Letter size
•
High-precision ruler
Perform adjustment as follows.
1
Load the paper.
•
Attaching the Roll Holder to Rolls
➔
P.12
•
Loading Rolls in the Printer
➔
P.14
•
Loading Sheets in the Printer
➔
P.20
Important
•
Always make sure the loaded paper matches the type of paper specified. Adjustment cannot be com-
pleted correctly unless the loaded paper matches the settings.
2
On the
Tab Selection screen
of the Control Panel, press
◀
or
▶
to select the Settings/Adj. tab (
).
Note
•
If the
Tab Selection screen
is not displayed, press the
Menu
button.
3
Press the
OK
button.
The
Set./Adj. Menu
is displayed.
iPF770 Series
Adjusting Line Length
Basic Guide
Adjustments for Better Print Quality
Adjusting the feed amount
81